YOKOGAWA DL850 ScopeCorder Скачать руководство пользователя страница 157

Страница: 157 / 190

6-49

IM DL850-03EN

Specifications

App

Index

CAN Bus Monitor Module (720240) Specification

Item

Specifications

Standard operating

condition

Ambient temperature: 23±5°C
Ambient humidity: 20 to 80% RH

Number of input ports

Maximum sample rate

100 kS/s

Input format

Isolated unbalanced

Maximum input voltage

–3 to +10 V (between CAN_H and GND or CAN_L and GND)

Maximum allowable

common mode voltage

42 V (DC+ACpeak) (CAT II, 30 Vrms)

Input connector

D-sub 9 pin (male)

Terminator

Internal, can be enabled or disabled for each port

Supported protocol

Physical layer: ISO-11898 (High Speed Communication)

Supported bit rates

10 kbps, 20 kbps, 33.3 kbps, 50 kbps, 62.5 kbps, 66.7 kbps, 83.3 kbps, 100 kbps, 125 kbps,

250 kbps, 500 kbps, 800 kbps, 1 Mbps

LED display

Illuminates to indicate that the terminator is enabled

Number of sub channels

16 sub channels/ports (60 for firmware versions 1.20 and later)

One shot output

Frames can be output in single shots

Terminator resistance

(when the terminator is

enabled)

110 to 130 Ω

A/D converter resolution

(when Value Type is set to

Float

)

16 bits, 2400 LSB/div

1 Low-speed CAN at low-speed transceiver levels is not supported. The 100 kbps covers firmware versions 1.30 and later of the

DL850/DL850V.

2 Applies to modules whose firmware version is 1.20 and later

6.13 Module Specifications

Содержание DL850 ScopeCorder































































































































































































Результаты поиска

Содержание DL850 ScopeCorder

Отзывы:

YOKOGAWA DL850 ScopeCorder, Руководство пользователя, Страница: 157 / 190

Результаты поиска

Содержание DL850 ScopeCorder

Отзывы: