YOKOGAWA DL850 ScopeCorder Скачать руководство пользователя страница 158

Страница: 158 / 190

6-50

IM DL850-03EN

CAN & LIN Bus Monitor Module (720241) Specification

Item

Specifications

Standard operating

condition

Ambient temperature: 23±5°C
Ambient humidity: 20 to 80% RH

Number of input ports

CAN port: 1. LIN port: 1.

Maximum sample rate

100 kS/s

Input format

Isolated unbalanced

CAN port specifications

Item

Specifications

Maximum input voltage

–3 to +10 V (between CAN_H and GND or CAN_L and GND)

Maximum allowable

common mode voltage

42 V (DC+ACpeak) (CAT II, 30 Vrms)

Input connector

D-sub 9 pin (male)

Terminator

Internal, can be enabled or disabled

Terminator resistance

(when the terminator is

enabled)

110 to 130 Ω

LED display

Illuminates to indicate that the terminator is enabled

Supported protocol

Physical layer: ISO-11898 (High Speed Communication)

Supported bit rates

10 kbps, 20 kbps, 33.3 kbps, 50 kbps, 62.5 kbps, 66.7 kbps, 83.3 kbps, 100 kbps, 125 kbps,

250 kbps, 500 kbps, 800 kbps, 1 Mbps

Supported data length

4 bytes maximum

Number of sub channels

60 sub channels

One shot output

Frames can be output in single shots

A/D converter resolution

(when Value Type is set to

Float)

16 bits, 2400 LSB/div

1 Low-speed CAN at low-speed transceiver levels is not supported.

LIN port specifications

Item

Specifications

Maximum input voltage

–0.3 to +18 V (between LIN.VBAT and GND)

Maximum allowable

common mode voltage

30 Vrms (CAT I and II)

Input connector

D-sub 9 pin (male)

Supported protocol

Physical layer: : Complies with ISO9141

Supported bit rates

2400bps, 9600bps, 19200bps

Supported data length

4 bytes maximum

Number of sub channels

60 sub channels

Supported check sums

Standard check sum, extended check sum

6.13 Module Specifications

Содержание DL850 ScopeCorder































































































































































































Результаты поиска

Содержание DL850 ScopeCorder

Отзывы:

YOKOGAWA DL850 ScopeCorder, Руководство пользователя, Страница: 158 / 190

Результаты поиска

Содержание DL850 ScopeCorder

Отзывы: