IM 701510-01E
15-4
No.
Message
Reference Page
700
Specified operation is currently in progress. Execute again after the current operation has been completed.
—
701
It is not possible to start acquisition since the specified operation is in progress.
—
702
It is not possible to save X-Y waveform data.
12-7
703
Designated trace is not displayed.
5-1
704
No set-up data has been stored.
11-3
705
No displayed waveform has been stored.
11-1
706
It is not possible to perform a snapshot during X-Y waveform display.
4-5
707
The roll chart is not secured.
10-2
708
No roll chart.
10-2
709
Printer is overheating. Turn OFF the power immediately. Contact your nearest YOKOGAWA representative. —
710
It is not possible to execute a self test since a storage media operation or printer operation, or GO/NO-GO
—
operation, or trigger action operaton is in progress.
711
It is not possible to perform this operation since GO/NO-GO is active. Stop GO/NO-GO and try again.
9-1, 8
712
No printer installed.
2
713
It is not possible to perform this operation since the trigger action is active. Stop the trigger action and
try again.
6-14
714
It is not possible to perform the real time printout in this time range. Set time range to 500ms/div or below.
10-10
715
It is not possible to perform the real time printout during Zoom/MainZoom waveform display, X-Y
waveform display, FFT waveform display or during loading/recalling a waveform.
10-10
716
(For DL1520)
It is not possible to perform real time printout with NORM/SINGLE as the trigger mode.
(For DL1540)
It is not possible to perform the real time printout with NORM/SGL (S)/ SGL (L)/ N-SGL as the trigger
mode or with history mode.
(For DL1520L/DL1540L)
It is not possible to perform the real time printout with NORM/SINGLE/ N-SGL as the trigger mode or with
history mode.
10-10
717
It is not possible to display a time stamp during acquisition.
7-9
718
It is not possible to use the ALL display during acquisition.
7-9
720
It is not possible to perform the real time printout using the external clock as timebase.
10-10
721
(For DL1520)
It is not possible to perform this action while averaging is active.
(For DL1520L/DL1540/DL1540L)
It is not possible to perform this action while averaging or history mode is active.
—
722
CAL-OUT is not connected.
—
723
Low temperature error has been detected in printer.
—
724
It is not possible to execute measurement of acquisition data (All Scan EXEC) because automatic
measurement of waveform parameter is OFF, or because data acquisition is in progress.
8-9
725
(For DL1520L/DL1540L)
It is not possible to perform the real time printout since the record length 1K words.
10-10
726
(For DL1520/DL1520L)
No centronics interface.
2, 10-11
728
(For DL1520/DL1520L)
Centronics printer off-line.
—
730
(For DL1520/DL1520L)
Centronics interface in use.
10-11
731
(For DL1520/DL1520L)
Can’t detect printer.
10-11
800
(For DL1520)
It is not possible to set the time range during SINGLE as the trigger mode.
(For DL1540)
It is not possible to set the time range during SGL(L)/N-SGL as the trigger mode or history mode.
(For DL1520L)
It is not possible to carry out this time range setting, because the trigger mode is N-SGL, the history mode
is active or the record length is 400K/1M words.
(For DL1540L)
It is not possible to carry out this time range setting, because the trigger mode is N-SGL, the history mode
5-11, 6-13,
is active or the record length is 400K/1M/2M words.
7-10
801
It is not possible to select an external clock in Envelope mode.
5-9
802
Delay time was set to “0s” as an external clock was selected.
5-9
803
It is not possible to set a delay time since an external clock has been selected.
5-9
15.2
Error Messages and Corrective Actions
