YOKOGAWA DL 1520 Скачать руководство пользователя страница 23

Страница: 23 / 201

3-4

IM 701510-01E

Connecting the SCSI cable

CAUTION

• When connecting or disconnecting the SCSI cable, turn the power switches

OFF on all equipment. Not doing so may cause malfunction, or damage the
equipment.

• Never short the connector pins on any equipment or externally apply

voltage to them. It may damage the equipment.

Before connecting
1.

Make sure to read the instruction manuals thoroughly and have a good understanding on
all equipment being connected beforehand.

Turn the power switches OFF on all equipment that are being connected.

Connecting DL1520L and the SCSI device
3.

Connect one end of the SCSI cable to the connector "OPTION" on the rear panel of this
unit.

Connect the other end of the SCSI cable to the connector on the SCSI device.

Set the ID number of the SCSI device to "5."

DL1520L digital oscilloscope (suffix code -C4)

"OPTION"
connector

SCSI device

SCSI cable
(To be provided by the customer)

Note

DL1520L with suffix code -C4 can connect one SCSI device to the "OPTION" connector.

3.3 Connecting the SCSI cable (for DL1520L with suffix code -C4)

Содержание DL 1520










































































































































































































Результаты поиска

Содержание DL 1520

Отзывы:

Похожие инструкции для DL 1520

Бренды по названию

Популярные бренды

YOKOGAWA DL 1520, Руководство пользователя

Результаты поиска

Содержание DL 1520

Отзывы:

Похожие инструкции для DL 1520

Бренды по названию

Популярные бренды