YOKOGAWA DL 1520 Скачать руководство пользователя страница 110

Страница: 110 / 201

9-8

IM 701510-01E

9.2

Judging using Measured Values of Waveform
Parameters

Operating Procedure

Press the

GO/NO-GO key

to display the GO/NO-GO setting menu.

Press the “

Mode

” soft key and select “

”. The GO/NO-GO top menu appears.

Press the “

PRMTR

” soft key. The default setting is “

ZONE

”.

The parameters which can be selected/set at this setting consist of the following.
• Determination range (refer to page 9-8);
• Determination conditions, such as parameter setup, determination logic, sequence

determination, and action after determination (refer to page 9-9, 9-10);

• Executing/aborting determination after setting/selecting the parameters. (refer to page 9-

10).

Setting the determination range
4.

After having pressed the “

T-Range

” soft key, select either “

” or “

” to set either

boudary of the determination range. Then use the rotary knob to edit the boundary
position. You may also use the

keys. Do this for both the left (T1) and right side

boundary (T2).

T1 cursor

T2 cursor

Determination range

Relevant Keys

Rotary knob

Soft keys

SELECT key

ESC key

<, > keys

GO/NO-GO key

RESET key

Содержание DL 1520










































































































































































































Результаты поиска

Содержание DL 1520

Отзывы:

Похожие инструкции для DL 1520

Бренды по названию

Популярные бренды

YOKOGAWA DL 1520, Руководство пользователя

Результаты поиска

Содержание DL 1520

Отзывы:

Похожие инструкции для DL 1520

Бренды по названию

Популярные бренды