YASKAWA SGD7S-xxxDA0 series Скачать руководство пользователя страница 178 | Manualshive

Страница: 178 / 636

background image

6.12 Motor Stopping Methods for Servo OFF and Alarms

6.12.1 Stopping Method for Servo OFF

6-38

6.12.1

Stopping Method for Servo OFF

Set the stopping method for when the servo is turned OFF in Pn001 = n.



X (Servo OFF or

Alarm Group 1 Stopping Method).

To use the dynamic brake to stop the motor, set Pn001 to n.



0 or n.



1.

If you do not connect an external dynamic brake, set Pn001 to n.



2 (Coast the motor to a

stop without the dynamic brake).

*

The Servomotor will coast to a stop when the SERVOPACK is not equipped with a built-in Dynamic Brake Resistor
or an External Dynamic Brake Resistor is not connected.

Note: If Pn001 is set to n.



0 (Stop the motor by applying the dynamic brake) and the Servomotor is stopped or

operates at a low speed, braking force may not be generated, just like it is not generated for coasting to a
stop.

6.12.2

Servomotor Stopping Method for Alarms

There are two types of alarms, group 1 (Gr. 1) alarms and group 2 (Gr. 2) alarms. A different
parameter is used to set the stopping method for alarms for each alarm type.

Refer to the following section to see which alarms are in group 1 and which are in group 2.

16.2.1 List of Alarms

Motor Stopping Method for Group 1 Alarms

When a group 1 alarm occurs, the Servomotor will stop according to the setting of Pn001 =
n.



X. The default setting is to stop by applying the dynamic brake.

Refer to the following section for details.

6.12.1 Stopping Method for Servo OFF

Motor Stopping Method for Group 2 Alarms

When a group 2 alarm occurs, the Servomotor will stop according to the settings of the follow-
ing three parameters. The default setting is for zero clamping.

•

Pn001 = n.



X (Servo OFF or Alarm Group 1 Stopping Method)

•

Pn00A = n.



X (Motor Stopping Method for Group 2 Alarms)

•

Pn00B = n.



X



(Motor Stopping Method for Group 2 Alarms)

However, during torque control, the group 1 stopping method is always used.
If you set Pn00B to n.



1



(Apply dynamic brake or coast Servomotor to a stop), you can

use the same stopping method as group 1. If you are coordinating a number of Servomotors,
you can use this stopping method to prevent machine damage that may result because of dif-
ferences in the stopping method.

The following table shows the combinations of the parameter settings and the resulting stop-
ping methods.

Parameter

Servomotor Stop-

ping Method

Status after Servo-

motor Stops

When Enabled

Classifi-

cation

Pn001
(2001h)

n.



0

(default setting)

Dynamic brake

*

Dynamic brake

*

After restart

Setup

n.



1

Coasting

n.



2

Coasting Coasting

When connecting an external dynamic brake circuit to SGD7S-210D, -260D, -280D, and -370D
SERVOPACKs, set the /DBANS (Dynamic Brake Answer Input) and /DBON (Dynamic Brake
Operation Request Output) signals regardless of the setting of Pn001 = n.



X. The A.F30

(Dynamic Brake Circuit Error) alarm will occur if the /DBANS and /DBON signals are not con-
nected to I/O signal terminals.

Important

«
...
176
177
178
179
180
...
»

Содержание SGD7S-xxxDA0 series





























































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SGD7S-xxxDA0 series

Бренд: Lakeshore Страницы: 192

Бренд: QUAD Страницы: 16

Бренд: Aalborg Страницы: 15

Бренд: Aalborg Страницы: 48

Бренд: Barthelme Страницы: 8

Бренд: CAB Страницы: 28

Бренд: C-TEC Страницы: 16

Бренд: C&T Solution Страницы: 27

SECURIT ST800L+

Бренд: C&K systems Страницы: 16

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

Бренд: Mamas & Papas Страницы: 24

Бренд: Mamas & Papas Страницы: 24

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 34

Бренд: S&C Страницы: 32

IntelliCap Plus

Бренд: S&C Страницы: 32

Бренд: S&P Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды