Yamaha YZ 2023 Series Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 378

background image

STARTING AND BREAK-IN

1-24

EAM20123

STARTING AND BREAK-IN

EAM30193

FUEL

Always use the recommended fuel as stated be-
low. Also, be sure to use new gasoline the day
of a race.

NOTICE

ECA24180

Use only unleaded gasoline. The use of lead-

ed gasoline will cause severe damage to the

engine internal parts such as valves, piston

rings, and exhaust system, etc.

TIP

Your Yamaha engine has been designed to use
unleaded gasoline with a pump octane number
[(R+M)/2] of 91 or higher, or a research octane
number of 95 or higher. If knocking (or pinging)
occurs, use a gasoline of a different brand.

WARNING

EWA19010

• For refueling, be sure to stop the engine

and use enough care not to spill any fuel.

Also be sure to avoid refueling close to a

fire.

• Refuel after the engine, exhaust pipe, etc.

have cooled off.

Gasohol

There are two types of gasohol: gasohol con-
taining ethanol and that containing methanol.
Gasohol containing ethanol can be used if the
ethanol content does not exceed 10 %. Gasohol
containing methanol is not recommended by
Yamaha because it can cause damage to the
fuel system or vehicle performance problems.

EAM30196

STARTING A COLD ENGINE

1. Press the shift pedal to neutral.
2. Push the starter knob “1” completely.

TIP

•

When the ambient temperature is 15



C (59



F)

or below, use the starter knob.

•

Do not operate the throttle grip when operating
the starter knob.

3. Start the engine by pushing the start switch.

If the engine fails to start when using the start
switch, release it, wait a few seconds, and
then try again.
Each starting attempt should be as short as
possible to preserve the battery. Do not crank
the engine more than 10 seconds on any one
attempt.

4. When the engine starts running, warm this up

one or two minutes at a steady speed (of
3000 to 5000 r/min), and then return the start-
er knob to its original position.

TIP

When operating the throttle grip in the closing di-
rection, the starter knob “1” moves in the direc-
tion as shown and returns to its original position.

WARNING

EWA19030

Since exhaust gas contains harmful ingredi-

ents, do not start or warm it up at an illventi-

lated place or a closed narrow place.

5. To stop the engine, push the engine stop

switch “1”.

TIP

Continue pushing the engine stop switch till the
engine comes to a full stop.

Recommended fuel

Unleaded gasoline (E10 accept-

able)

Octane number (R+M)/2

91 or higher

Fuel tank capacity

8.2 L (2.2 US gal, 1.8 Imp.gal)

Fuel reserve amount

2.0 L (0.53 US gal, 0.44 Imp.gal)

1

1

1

1

«
...
34
35
36
37
38
...
»

Содержание YZ 2023 Series



























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2023 Series

Бренд: hepco & becker Страницы: 5

Freeride E-XC 2019

Бренд: KTM Страницы: 44

Бренд: B-PWR Страницы: 13

Бренд: Honda Страницы: 110

Бренд: KTM Страницы: 38

H-X-ADV-07-01-AL

Бренд: SRC Страницы: 6

Бренд: Puch Страницы: 151

Бренд: KTM Страницы: 25

Бренд: Blata Страницы: 17

Бренд: B&G electronics Страницы: 3

Бренд: MRA Страницы: 6

Бренд: Baja motorsports Страницы: 20

Бренд: Caberg Страницы: 16

Бренд: Yamaha Страницы: 26

Бренд: Yamaha Страницы: 58

Бренд: Yamaha Страницы: 42

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 77

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды