Yamaha YZ 2023 Series Скачать руководство пользователя страница 134

Страница: 134 / 378

FRONT BRAKE

4-20

cleaning and lubricating.

• Never use solvents on internal brake com-

ponents as they will cause the piston seals

to swell and distort.

• When the brake caliper is disassembled, re-

place the brake caliper piston seal and the

brake caliper piston dust seal with new

ones.

EAM30035

INSTALLING THE FRONT BRAKE CALIPER

1. Install:

•

Front brake caliper bracket

•

Front brake caliper
(temporarily)

•

Copper washer

•

Brake hose

•

Union bolt

WARNING

EWA13531

Proper brake hose routing is essential to in-

sure safe vehicle operation.

NOTICE

ECA24460

Make sure that the pipe portion “a” of the

brake hose touches the projection “b” on the

brake caliper.

2. Install:

•

Front brake caliper

•

Brake pad spring

•

Brake pad

•

Brake pad pin

•

Brake hose holder

Refer to “CHECKING THE FRONT BRAKE
PADS” on page 3-24.

3. Tighten:

•

Brake hose holder bolt “1”

TIP

Make sure that the brake hose holder “2” is in-
stalled with its upper end “a” aligned with the
paint “b” on the brake hose.

4. Pour brake fluid to the brake master cylinder

reservoir up to the specified level.

WARNING

EWA13090

• Use only the designated brake fluid. Other

brake fluids may cause the rubber seals to

deteriorate, causing leakage and poor

brake performance.

• Refill with the same type of brake fluid that

is already in the system. Mixing brake fluids

may result in a harmful chemical reaction,

leading to poor brake performance.

• When refilling, be careful that water does

not enter the brake fluid reservoir. Water

will significantly lower the boiling point of

the brake fluid and could cause vapor lock.

NOTICE

ECA13540

Brake fluid may damage painted surfaces

and plastic parts. Therefore, always clean up

any spilt brake fluid immediately.

5. Bleed:

•

Brake system

Specified brake fluid

DOT 4

Front brake caliper bolt

28 N·m (2.8 kgf·m, 21 lb·ft)

Brake hose union bolt

30 N·m (3.0 kgf·m, 22 lb·ft)

Brake pad pin

17 N·m (1.7 kgf·m, 13 lb·ft)

Brake hose holder bolt

9 N·m (0.9 kgf·m, 6.6 lb·ft)

Specified brake fluid

DOT 4

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды