Yamaha YZ 2023 Series Скачать руководство пользователя страница 160

Страница: 160 / 378

FRONT FORK

4-46

EAM30058

ASSEMBLING THE FRONT FORK LEGS

WARNING

EWA13660

• Make sure the oil levels in both front fork

legs are equal.

• Uneven oil levels can result in poor han-

dling and a loss of stability.

TIP

•

When assembling the front fork leg, be sure to
replace the following parts:

•

Inner tube bushing

•

Slide metal

•

Oil seal

•

Copper washer

•

Before assembling the front fork leg, make
sure that all of the components are clean.

1. Stretch the damper assembly fully.
2. Fill:

•

Damper assembly

NOTICE

ECA24530

• Be sure to use the recommended oil. Other

oils may have an adverse effect on front

fork performance.

• When disassembling and assembling the

front fork leg, take care not to allow any for-

eign material to enter the front fork.

3. After filling, pump the damper assembly “1”

slowly up and down (about 200 mm (7.9 in)
stroke) several times to bleed the damper as-
sembly of air.

TIP

Avoid excessive full stroke. A stroke of 200 mm
(7.9 in) or more will cause air to enter. In this
case, repeat the steps (1) to (3).

4. Measure:

•

Oil level (left and right) “a”
Out of specification



Regulate.

5. Tighten:

•

Locknut “1”

TIP

Fully finger tighten the locknut onto the damper
assembly.

6. Loosen:

•

Compression damping force adjuster “1”

TIP

•

Before loosening the damping force adjuster,
record the setting position.

•

Unless the damping force adjuster is fully loos-
ened, correct damping characteristic cannot be

Recommended oil

Yamaha Suspension Oil S1

Standard oil amount

216 cm³ (7.30 US oz, 7.62 Imp.oz)

Standard oil level

145–148 mm (5.71–5.83 in)

From top of fully stretched

damper assembly.

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды