Yamaha YZ 2023 Series Скачать руководство пользователя страница 131

Страница: 131 / 378

FRONT BRAKE

4-17

EAM30028

INTRODUCTION

WARNING

EWA19210

If you need to disassemble the disc brake

components, observe the following precau-

tions.

• Never disassemble the brake components

unless absolutely necessary.

• If there is any problem with connections on

the hydraulic brake system, perform the

following jobs. Disassemble the brake sys-

tem, drain the brake fluid, and clean it. After

that, add a suitable amount of brake fluid.

Then, bleed it after reassembly.

• Use only brake fluid for washing brake

components.

• Use new brake fluid for cleaning the brake

components.

• Immediately wipe off the spilled brake fluid

to avoid damage to painted surfaces or

plastic parts.

• Handle brake fluid with special care not to

let it enter your eyes so that you may not

lost your eyesight.

• FIRST AID FOR BRAKE FLUID ENTERING

THE EYES:

• Flush with water for 15 minutes and get im-

mediate medical attention.

EAM30029

CHECKING THE FRONT BRAKE DISC

1. Check:

•

Front brake disc
Damage/galling



Replace.

2. Measure:

•

Brake disc thickness
Measure the brake disc thickness at a few dif-
ferent locations.
Out of specification



Replace.

3. Measure:

•

Brake disc runout
Out of specification



Replace the brake

disc.

a. Place the vehicle on a maintenance stand

so that the front wheel is elevated.

b. Remove the brake caliper.
c. Hold the dial gauge at a right angle against

the brake disc surface.

d. Measure the runout 1.5 mm (0.06 in)

above the brake disc edge.

4. Replace:

•

Brake disc
Refer to “ASSEMBLING THE FRONT
WHEEL” on page 4-6.

EAM30519

REPLACING THE FRONT BRAKE PADS

TIP

When replacing the brake pads, it is not neces-
sary to disconnect the brake hose or disassem-
ble the brake caliper.

1. Remove:

•

Brake pad
a. Remove the pad pin plug “1”.

b. Loosen the pad pin “2”.
c. Remove the brake caliper “3” from the

front fork.

Brake disc thickness limit

2.5 mm (0.10 in)

Brake disc runout limit (as mea-

sured on wheel)

0.15 mm (0.0059 in)

G098641

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды