Yamaha YZ 2023 Series Скачать руководство пользователя страница 206

Страница: 206 / 378

CAMSHAFT

5-19

b. With the tensioner rod fully wound and the

chain tensioner “UP” mark “a” facing up-
ward, install the gasket “1”, the timing
chain tensioner “2” and tighten the bolts
“3”.

c. Release the screwdriver, check that the

tensioner rod comes out smoothly, and
tighten the gasket “4” and the cap bolt “5”.

3. Turn:

•

Crankshaft
Counterclockwise several turns.

4. Check:

•

Top dead center (TDC) mark on the genera-
tor rotor
Align with the crankcase alignment mark.

•

Camshaft match marks
Align with the cylinder head surface.
Out of alignment



Adjust.

5. Install:

•

Timing chain guide (top side) “1”

•

Cylinder head cover gasket “2”

•

Cylinder head cover “3”

•

Bolt (cylinder head cover) “4”

TIP

Before installation, apply the sealant to the cylin-
der head cover gasket.

6. Install:

•

Cylinder head breather hose

•

Spark plug

Bolt (timing chain tensioner)

10 N·m (1.0 kgf·m, 7.4 lb·ft)

Timing chain tensioner cap bolt

6 N·m (0.6 kgf·m, 4.4 lb·ft)

Bolt (cylinder head cover)

10 N·m (1.0 kgf·m, 7.4 lb·ft)

Yamaha bond No. 1215

90890-85505

Three bond No. 1215®

Spark plug

13 N·m (1.3 kgf·m, 9.6 lb·ft)

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды