Yamaha YZ 2023 Series Скачать руководство пользователя страница 161

Страница: 161 / 378

FRONT FORK

4-47

obtained after installation.

7. Install:

•

Base valve “1”
(to the damper assembly “2”)

TIP

First bring the damper rod pressure to a maxi-
mum. Then install the base valve while releasing
the damper rod pressure.

8. Check:

•

Damper assembly
Not fully stretched



Repeat the steps (1) to

(7).

9. Tighten:

•

Base valve “1”

TIP

Hold the damper assembly with the cap bolt ring
wrench “2” and use the cap bolt wrench “3” to
tighten the base valve.

10.After filling, pump the damper assembly “1”

slowly up and down more than 10 times to
distribute the fork oil.

11.While protecting the damper assembly “1”

with a cloth and compressing fully, allow ex-
cessive oil to overflow on the base valve side.

NOTICE

ECA24540

Take care not to damage the damper assem-

bly.

12.Allow the overflowing oil to escape at the hole

“a” in the damper assembly.

TIP

The overflow measures about 10 cm³ (0.34
US oz, 0.35 Imp.oz).

Base valve

28 N·m (2.8 kgf·m, 21 lb·ft)

Cap bolt wrench

90890-01500

Cap bolt wrench

YM-01500

Cap bolt ring wrench

90890-01501

Cap bolt ring wrench

YM-01501

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды