manualshive.com logo in svg

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Yamaha YZ Серия 2023 - это мощный мотоцикл для профессиональных гонщиков. Владельцы могут легко получить Owner's Service Manual для этой серии, скачав его бесплатно с нашего сайта. Этот исчерпывающий руководство поможет вам успешно управлять и обслуживать ваш мотоцикл. Скачать на manualshive.com.

Поделиться
Скачать
background image

FUEL INJECTION SYSTEM

8-33

Fault code No. 33

3

Faulty ECU.

Execute the diagnostic mode. 

(Code No. 08)

When the vehicle is upright:

0.4–1.4 (V)

When the vehicle is overturned:

3.7–4.4 (V)

Improper display 

 Replace the 

ECU.

Service is finished.

4

Delete the fault code.

Confirm that the fault code has 

a condition of “Recovered” 

using the Yamaha diagnostic 

tool, and then delete the fault 

code.

Fault code No.

33

Item

Ignition coil: open or short circuit detected in the primary lead of 

the ignition coil.

Fail-safe system

Unable to start engine

Unable to drive vehicle

Diagnostic code No.

30

Actuation

Actuates the ignition coil five times at one-second intervals.

“WARNING” on the Yamaha diagnostic tool blinks five times when the 

ignition coil is actuated.

Procedure

Check that a spark is generated five times.

•

Connect an ignition checker.

Item

Probable cause of malfunc-

tion and check

Maintenance job

Confirmation of service com-

pletion

1

Connection of ignition coil cou-

pler.

Check the locking condition of 

the coupler.

Disconnect the coupler, and 

check the pins (for bent or bro-

ken terminals and locking condi-

tion of the pins).

Improperly connected 

 Con-

nect the coupler securely, or 

repair/replace the wire harness.

Start the engine and let it idle for 

approximately 5 seconds.

Check the condition of the fault 

code using the malfunction 

mode of the Yamaha diagnostic 

tool.

Condition is “Recovered” 

 Go 

to item 8 and finish the service.

Condition is “Detected” 

 Go to 

item 2.

2

Connection of wire harness 

ECU coupler.

Check the locking condition of 

the coupler.

Disconnect the coupler, and 

check the pins (for bent or bro-

ken terminals and locking condi-

tion of the pins).

Improperly connected 

 Con-

nect the coupler securely, or 

repair/replace the wire harness.

Start the engine and let it idle for 

approximately 5 seconds.

Check the condition of the fault 

code using the malfunction 

mode of the Yamaha diagnostic 

tool.

Condition is “Recovered” 

 Go 

to item 8 and finish the service.

Condition is “Detected” 

 Go to 

item 3.

Fault code No.

30

Item

The vehicle has overturned.

Содержание YZ 2023 Series



























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2023 Series

N-Com B902L User Instructions And Safety preview
B902L
Бренд: N-Com Страницы: 36
R&G CP0485 Fitting Instructions Manual preview
CP0485
Бренд: R&G Страницы: 47
MOTO GUZZI V 7 CAFE CLASSIC Manual preview
V 7 CAFE CLASSIC
Бренд: MOTO GUZZI Страницы: 147
Can-Am Spyder RT Series Instructions Manual preview
Spyder RT Series
Бренд: Can-Am Страницы: 52
MRA 4025066152438 Mounting Instructions preview
4025066152438
Бренд: MRA Страницы: 8
Honda CBR150R Owner'S Manual preview
CBR150R
Бренд: Honda Страницы: 98
hepco & becker 504980 00 05 Quick Manual preview
504980 00 05
Бренд: hepco & becker Страницы: 2
DYNATEK D3K3-1 Installation Instructions preview
D3K3-1
Бренд: DYNATEK Страницы: 4
DYNATEK DDK2-16 Installation Instructions Manual preview
DDK2-16
Бренд: DYNATEK Страницы: 7
Caberg XTRACE Manual preview
XTRACE
Бренд: Caberg Страницы: 16
hepco & becker 5039515 00 05 Quick Start Manual preview
5039515 00 05
Бренд: hepco & becker Страницы: 3
hepco & becker 5066502 00 09 Quick Start Manual preview
5066502 00 09
Бренд: hepco & becker Страницы: 2
Yamaha ET250 1980 Manual preview
ET250 1980
Бренд: Yamaha Страницы: 22
Yamaha DT50M Manual And Manual preview
DT50M
Бренд: Yamaha Страницы: 24
Yamaha E115M Owner'S Manual preview
E115M
Бренд: Yamaha Страницы: 61
Yamaha Fino 125 Manual preview
Fino 125
Бренд: Yamaha Страницы: 78
Yamaha Fazer Owner'S Manual preview
Fazer
Бренд: Yamaha Страницы: 79
Yamaha FAZER FZS1000 Owner'S Manual preview
FAZER FZS1000
Бренд: Yamaha Страницы: 94

Бренды по названию

Популярные бренды

Загрузить еще бренды