Yamaha YZ 2023 Series Скачать руководство пользователя страница 356

Страница: 356 / 378

TROUBLESHOOTING

9-9

Front fork is soft

Fatigued or broken fork spring

Replace the fork spring.

Incorrect oil viscosity (low)

Change to recommended fork oil.

Incorrect oil level (low)

Adjust to the specified oil level.

Improperly adjusted spring pre-

load (soft)

Adjust the spring preload.

Improperly adjusted rebound

damping (soft)

Adjust the rebound damping.

Improperly adjusted compression

damping (soft)

Adjust the compression damping.

Leaking oil from front fork

Bent, damaged, or corroded inner

tube

Replace the inner tube.

Cracked or damaged outer tube

Replace the outer tube.

Improperly installed oil seal

Replace the oil seal.

Damaged oil seal lip

Replace the oil seal.

Incorrect oil level (high)

Adjust to the specified oil level.

Loose damper rod assembly bolt

Tighten the damper rod assembly

bolt to the specified torque.

Damaged damper rod assembly

bolt copper washer

Replace the damper rod assembly

bolt copper washer.

Cracked or damaged cap bolt O-

ring

Replace the cap bolt O-ring.

Rear suspension is hard

Bent or damaged rear shock

absorber rod

Replace the rear shock absorber.

Bent swingarm pivot shaft

Replace the swingarm pivot shaft.

Damaged or worn swingarm bear-

ing or bushing

Replace the swingarm bearing or

bushing.

Damaged or worn relay arm bear-

ing

Replace the relay arm bearing.

Damaged or worn connecting arm

bearing

Replace the connecting arm bear-

ing.

Improperly adjusted rear shock

absorber spring preload (hard)

Adjust the spring preload.

Improperly adjusted rear shock

absorber rebound damping (hard) Adjust the rebound damping.

Improperly adjusted rear shock

absorber compression damping

(hard)

Adjust the compression damping.

Symptom

Possible cause

Actions

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды