Yamaha YZ 2023 Series Скачать руководство пользователя страница 278

Страница: 278 / 378

FUEL TANK

7-3

EAM30266

INSTALLING THE FUEL PUMP

1. Install:

•

Fuel pump gasket

•

Fuel filter

•

Fuel pump

•

Fuel pump bracket

TIP

•

Take care not to damage the installation sur-
faces of the fuel tank.

•

Always use a new fuel pump gasket.

•

Install the lip on the fuel pump gasket upward.

•

Install the fuel pump as shown in the figure.

•

Align the projection “a” on the fuel pump with
the slot “b” in the fuel pump bracket.

•

Tighten the fuel pump bolts in the proper tight-
ening sequence as shown.

EAM30267

INSTALLING THE FUEL TANK

1. Install:

•

Fuel tank

2. Connect:

•

Fuel hose

NOTICE

ECA24740

• Connect the fuel hose securely, and check

that the orientation of the installed fuel

hose holder is correct.

• Take care not to kink or pinch the fuel hose.

TIP

•

Insert the fuel hose into the fuel pipe securely
until you hear a “click”.

•

Slide the fuel hose connector cover “1” at the
hose end in the direction of the arrow.

•

Install the fuel hose connector holder “a”.

•

Check that the fuel hose and the fuel pump
lead are routed through the guide on the cover.

3. Connect:

•

Fuel pump coupler

4. Install:

•

Air scoop (left/right)

•

Seat

•

Side cover (left/right)
Refer to “GENERAL CHASSIS” on page 4-1.

Fuel pump bolt

7 N·m (0.7 kgf·m, 5.2 lb·ft)

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца, Страница: 278 / 378

Результаты поиска

Содержание YZ 2023 Series

Отзывы: