Yamaha YZ 2023 Series Скачать руководство пользователя страница 340

Страница: 340 / 378

ELECTRICAL COMPONENTS

8-53

a. Disconnect the diode from the wire har-

ness.

b. Connect the digital circuit tester (



) to the

diode coupler as shown.

c. Check the diode for continuity.
d. Check the diode for no continuity.

EAM30294

CHECKING THE IGNITION SPARK GAP

1. Check:

•

Ignition spark gap
Out of specification



Perform the ignition

system troubleshooting, starting with step (5).
Refer to “TROUBLESHOOTING” on page
8-3.

TIP

If the ignition spark gap is within specification,
the ignition system circuit is operating normally.

a. Remove the spark plug cap from the spark

plug.

b. Connect the ignition checker “1” as

shown.

c. Crank the engine, and measure the igni-

tion spark gap “a”.

d. Crank the engine, and gradually increase

the spark gap until a misfire occurs.

EAM30295

CHECKING THE SPARK PLUG CAP

1. Remove:

•

Spark plug cap
(from the spark plug lead)

2. Check:

•

Spark plug cap resistance
Out of specification



Replace.

a. Connect the digital circuit tester (



) to the

spark plug cap.

No continuity

Positive tester prove



Blue/Green “1”

Negative tester prove



Blue

“2”

Continuity

Positive tester prove



Blue “2”

Negative tester prove



Blue/Green “1”

No continuity

Positive tester prove



Brown/White, Brown “3”

Negative tester prove



Blue/Green, Blue/White “4”

Continuity

Positive tester prove



Blue/Green, Blue/White “4”

Negative tester prove



Brown/White, Brown “3”

No continuity

Positive tester prove



Blue/Black “5”

Negative tester prove



Blue/Red “6”

Continuity

Positive tester prove



Blue/Red “6”

Negative tester prove



Blue/Black “5”

A. Diode 1
B. Diode 2
C. Diode 3

L/G

L/B

L/R

Br/W,Br

L/G,
L/W

Minimum ignition spark gap

6.0 mm (0.24 in)

Ignition checker

90890-06754

Oppama pet–4000 spark checker

YM-34487

2. Spark plug cap

Resistance

7.50–12.50 k



Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды