Yamaha YZ 2023 Series Скачать руководство пользователя страница 323

Страница: 323 / 378

FUEL INJECTION SYSTEM

8-36

Fault code No. 41

Fault code No. 43

Delete the fault code.

Confirm that the fault code has

a condition of “Recovered”

using the Yamaha diagnostic

tool, and then delete the fault

code.

Fault code No.

Item

ECU: built-in lean angle sensor malfunction.

Fail-safe system

Unable to start engine

Able to drive vehicle

Diagnostic code No.

Diagnostic tool display

Displays the lean angle sensor output voltage.

•

0.4–1.4 (V) (upright)

•

3.7–4.4 (V) (overturned)

Procedure

Remove the ECU, and incline it 45



or more.

Item

Probable cause of malfunc-

tion and check

Maintenance job

Confirmation of service com-

pletion

Faulty ECU.

Replace the ECU.

Service is finished.

Fault code No.

Item

Fuel system voltage: incorrect voltage supplied to the main relay

and CCU.

Fail-safe system

Able to start engine

Able to drive vehicle

Diagnostic code No.

Diagnostic tool display

Fuel system voltage

Approximately 12.0 (V)

Procedure

Disconnect the main relay, and push the start switch.

Item

Probable cause of malfunc-

tion and check

Maintenance job

Confirmation of service com-

pletion

Connection of main relay cou-

pler.

Check the locking condition of

the coupler.

Disconnect the coupler, and

check the pins (bent or broken

terminals and locking condition

of the pins).

Improperly connected



Con-

nect the coupler securely, or

repair/replace the wire harness.

Press the start switch and the

engine stop switch alternately to

switch the power supply (= main

relay) from “ON



OFF



ON”.

Check the condition of the fault

code using the malfunction

mode of the Yamaha diagnostic

tool.

Condition is “Recovered”



to item 6 and finish the service.

Condition is “Detected”



Go to

item 2.

Fault code No.

Item

Injector: open or short circuit detected.

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды