Yamaha YZ 2023 Series Скачать руководство пользователя страница 342

Страница: 342 / 378

ELECTRICAL COMPONENTS

8-55

b. Measure the crankshaft position sensor

resistance.

EAM30298

CHECKING THE LEAN ANGLE SENSOR

1. Check:

•

Mounted condition of ECU
Improperly mounted



Remount.

TIP

•

The lean angle sensor is built into the ECU.

•

The lean angle sensor stops the engine in case
of a turnover.

•

To ensure that the lean angle sensor operates
correctly, do not change the installed condition
of the ECU.

EAM30299

CHECKING THE STARTER MOTOR

OPERATION

1. Check:

•

Starter motor operation
Does not operate



Perform the electric

starting system troubleshooting, starting with
step (4).
Refer to “TROUBLESHOOTING” on page
8-7.
a. Connect the positive battery terminal “1”

and starter motor lead “2” with a jumper
lead “3”.

WARNING

EWA13810

• A wire that is used as a jumper lead must

have at least the same capacity of the bat-

tery lead, otherwise the jumper lead may

burn.

• This check is likely to produce sparks,

therefore, make sure no flammable gas or

fluid is in the vicinity.

b. Check the starter motor operation.

EAM30300

CHECKING THE STATOR COIL

1. Disconnect:

•

Stator coil assembly coupler
(from the wire harness)

2. Check:

•

Stator coil assembly resistance
Out of specification



Replace.

a. Connect the digital circuit tester (



) to the

stator coil assembly coupler.

b. Measure the stator coil assembly resis-

tance.

EAM30301

CHECKING THE RECTIFIER/REGULATOR

1. Check:

•

Rectifier/regulator output voltage
Out of specification



Replace.

•

Positive tester probe



Gray “1”

•

Negative tester probe



Black “2”

Stator coil resistance

0.512–0.768



Digital circuit tester (CD732)

90890-03243

Model 88 Multimeter with tachom-

eter

YU-A1927

•

Positive tester probe



White “1”

•

Negative tester probe



White “2”

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды