Yamaha YZ 2023 Series Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 378

background image

STARTING AND BREAK-IN

1-25

EAM30197

STARTING A WARM ENGINE

Follow the same procedure as for starting a cold
engine with the exception that the starter is not
required when the engine is warm.

TIP

If the engine fail to start, fully open the throttle
grip and push the start switch few seconds to
clear the engine of the rich air-fuel mixture re-
tained in it.

EAM30198

BREAK-IN PROCEDURES

A break-in is important so that rotating portion,
sliding surfaces, and mounted areas may fit one
another, and that the rider may become accus-
tomed to the machine.

NOTICE

ECA25811

Before running, do maintenance on the air

filter element.

1. After warming up the engine, drive it for about

20 minutes at a throttle opening of 1/2 or less.

TIP

This model is equipped with an engine auto-stop
system. The engine stops automatically if left
idling for 7 minutes. If the engine stops, push the
start switch to restart the engine.

2. Make a pit stop, and check mounted areas for

looseness, oil leaks, or other problems.

3. Then, drive it for about 40 minutes at a throt-

tle opening of 3/4 or less.

4. Make a pit stop again, and thoroughly check

mounted areas for looseness, oil leaks, or
other problems. Thorough checks and ad-
justments are required in particular for stretch
of cables, free play of the brake, stretch of the
drive chain, looseness of the spoke, and so
on.

NOTICE

ECA25821

After a break-in or after each race, always

check the points shown in “TORQUE-

CHECK POINTS” for tightening torques and

retighten them.

Also when the following parts are replaced, a

break-in is required.

• Cylinder and Crankshaft: A break-in is re-

quired for about an hour.

• Piston, Piston ring, Valve, Camshaft, and

Gear: A break-in is required for about 30

minutes at a throttle opening of 1/2 or less.

Observe the condition of the engine carefully

during a break-in.

For checkpoints for a break-in, see “MAIN-

TENANCE AFTER BREAK-IN”. If any prob-

lem is found, immediately stop the engine

and make a checkup.

EAM30468

ENGINE STARTING PRECAUTION

•

Make sure the transmission is in neutral or be
sure to pull the clutch lever before pressing the
start switch.

WARNING

EWA20540

If the clutch lever is not pulled and the start

switch is pressed with the transmission in

gear, the starter motor will cause the rear

wheel to spin, which may cause injury.
•

When starting the engine, if only the starter
motor is turning but the engine does not crank,
this is a malfunction most likely due to a worn-
out starter clutch. Replace the starter clutch.

1

«
...
35
36
37
38
39
...
»

Содержание YZ 2023 Series



























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YZ 2023 Series

Бренд: rizoma Страницы: 10

Бренд: Wunderkind Custom Страницы: 4

Бренд: APRILIA Страницы: 151

250 EXC-F AUS 2012

Бренд: KTM Страницы: 18

PowerParts 44011076140

Бренд: KTM Страницы: 17

Бренд: Honda Страницы: 106

Goldwing GL1100 Interstate 1981

Бренд: Honda Страницы: 100

Бренд: Honda Страницы: 118

Бренд: Honda Страницы: 108

Бренд: Honda Страницы: 194

GL 1200 A '84 Aspencade

Бренд: Honda Страницы: 280

Бренд: Honda Страницы: 168

Бренд: HealTech Electronics Страницы: 3

Бренд: R&G Страницы: 6

Бренд: yasuni Страницы: 18

Бренд: hepco & becker Страницы: 3

Бренд: hepco & becker Страницы: 4

Бренд: hepco & becker Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды