Yamaha YZ 2023 Series Скачать руководство пользователя страница 120

Страница: 120 / 378

FRONT WHEEL

4-6

EAM30017

REMOVING THE FRONT WHEEL

1. Use a maintenance stand to raise the front

wheel off the ground.

WARNING

EWA13120

Securely support the vehicle so that there is

no danger of it falling over.

2. Remove:

•

Front wheel

EAM30019

DISASSEMBLING THE FRONT WHEEL

1. Remove:

•

Oil seal

•

Bearing
a. Clean the outside of the front wheel hub.
b. Remove the oil seals “1” with a flat-head

screwdriver.

TIP

To prevent damaging the wheel, place a rag “2”
between the screwdriver and the wheel surface.

c. Remove the bearings with a bearing pull-

er.

EAM30018

CHECKING THE FRONT WHEEL

1. Check:

•

Front wheel axle
Roll the front wheel axle on a flat surface.
Bends



Replace.

WARNING

EWA13460

Do not attempt to straighten a bent wheel ax-

le.

2. Check:

•

Tire

•

Front wheel
Damage/wear



Replace.

Refer to “CHECKING THE TIRES” on page
3-33 and “CHECKING THE WHEELS” on
page 3-33.

3. Check:

•

Spoke
Refer to “CHECKING AND TIGHTENING
THE SPOKES” on page 3-33.

4. Tighten:

•

Spoke
Refer to “CHECKING AND TIGHTENING
THE SPOKES” on page 3-33.

TIP

After tightening the spokes, measure the wheel
runout.

5. Measure:

•

Radial wheel runout “a”

•

Lateral wheel runout “b”
Out of specification



Repair/replace.

6. Check:

•

Collar
Damage/wear



Replace.

7. Check:

•

Bearing
Front wheel turns roughly or is loose



Re-

place the wheel bearings.

•

Oil seal
Damage/wear



Replace.

EAM30020

ASSEMBLING THE FRONT WHEEL

1. Install:

•

Bearing (left side) “1”

•

Spacer “2”

•

Bearing (right side) “3”

•

Oil seal “4”

TIP

•

Apply the lithium-soap-based grease to the oil
seal lip when installing.

Spoke

2.5 N·m (0.25 kgf·m, 1.8 lb·ft)

Radial wheel runout limit

2.0 mm (0.08 in)

Lateral wheel runout limit

2.0 mm (0.08 in)

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды