Yamaha YZ 2023 Series Скачать руководство пользователя страница 150

Страница: 150 / 378

HANDLEBAR

4-36

EAM30052

REMOVING THE HANDLEBAR

1. Stand the vehicle upright on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is

no danger of it falling over.

2. Remove:

•

Grip “1”

TIP

Blow in compressed air between the handlebar
or tube guide and the grip. Then remove the grip
which has become loose.

3. Remove:

•

Throttle cable housing “1”

•

Throttle grip “2”

TIP

While removing the throttle cable housing, pull
back the rubber cover “3”.

EAM30053

CHECKING THE HANDLEBAR

1. Check:

•

Handlebar
Bends/cracks/damage



Replace.

WARNING

EWA13690

Do not attempt to straighten a bent handle-

bar as this may dangerously weaken it.

EAM30054

INSTALLING THE HANDLEBAR

1. Stand the vehicle upright on a level surface.

WARNING

EWA13120

Securely support the vehicle so that there is

no danger of it falling over.

2. Install:

•

Damper “1”

•

Lower handlebar holder “2” (temporarily)

•

Handlebar “3”

•

Upper handlebar holder “4”

TIP

•

Install the lower handlebar holders with the
side having the longer distance “a” from the
mounting bolt center facing towards the rear
side of the vehicle.

•

Installing the lower handlebar holders in the re-
verse direction allow the front-to-rear offset
amount of the handlebar position to be
changed.

•

The upper handlebar holders should be in-
stalled with the punch marks “b” facing for-
ward.

•

When installing the handlebar, make sure that
right and left marks “c” are in place identically
on both sides.

•

Install the handlebar so that the projection “d”
of the upper handlebar holders is positioned at
the mark on the handlebar as shown.

NOTICE

ECA14250

• First, tighten the bolts on the front side of

the handlebar holder, and then on the rear

side.

• Turn the handlebar all the way to the left

and right. If there is any contact with the

fuel tank, adjust the handlebar position.

Upper handlebar holder bolt

28 N·m (2.8 kgf·m, 21 lb·ft)

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды