Yamaha YZ 2023 Series Скачать руководство пользователя страница 260

Страница: 260 / 378

TRANSMISSION

5-73

EAM30153

REMOVING THE TRANSMISSION

1. Remove:

•

Long shift fork guide bar “1”

•

Short shift fork guide bar “2”

•

Shift cam “3”

•

Shift fork 3 “4”

•

Shift fork 2 “5”

•

Shift fork 1 “6”

•

Main axle “7”

•

Drive axle “8”

•

Collar “9”

TIP

•

Remove assembly with the collar “9” installed
to the crankcase.

•

Make a note of the position of each part. Pay
particular attention to the location and direction
of shift forks.

•

Remove the main axle and the drive axle all to-
gether by tapping the drive axle lightly with a
soft hammer.

EAM30154

CHECKING THE SHIFT FORKS

1. Check:

•

Shift fork cam follower “1”

•

Shift fork pawl “2”
Bends/damage/scoring/wear



Replace the

shift fork.

2. Check:

•

Shift fork guide bar
Roll the shift fork guide bar on a flat surface.
Bends



Replace.

WARNING

EWA12840

Do not attempt to straighten a bent shift fork

guide bar.

3. Check:

•

Shift fork movement
(along the shift fork guide bar)
Rough movement



Replace the shift forks

and shift fork guide bar as a set.

EAM30155

CHECKING THE SHIFT DRUM ASSEMBLY

1. Check:

•

Shift drum groove
Damage/scratches/wear



Replace the shift

drum assembly.

•

Shift drum segment
Damage/wear



Replace the shift drum as-

sembly.

EAM30156

CHECKING THE TRANSMISSION

1. Measure:

•

Main axle runout
(with a centering device and dial gauge “1”)
Out of specification



Replace the main axle.

Main axle runout limit

0.08 mm (0.0032 in)

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды