Yamaha YZ 2023 Series Скачать руководство пользователя страница 100

Страница: 100 / 378

CHASSIS

3-24

WARNING

EWA13090

• Use only the designated brake fluid. Other

brake fluids may cause the rubber seals to

deteriorate, causing leakage and poor

brake performance.

• Refill with the same type of brake fluid that

is already in the system. Mixing brake fluids

may result in a harmful chemical reaction,

leading to poor brake performance.

• When refilling, be careful that water does

not enter the brake fluid reservoir. Water

will significantly lower the boiling point of

the brake fluid and could cause vapor lock.

NOTICE

ECA13540

Brake fluid may damage painted surfaces

and plastic parts. Therefore, always clean up

any spilt brake fluid immediately.

EAM30231

CHECKING THE FRONT BRAKE PADS

The following procedure applies to all of the
brake pads.
1. Operate the brake.
2. Check:

•

Front brake pad
Wear indicator grooves “1” almost touch the
brake disc



Replace the brake pads as a

set.
Refer to “FRONT BRAKE” on page 4-13.

EAM30232

CHECKING THE REAR BRAKE PADS

The following procedure applies to all of the
brake pads.
1. Operate the brake.
2. Check:

•

Rear brake pad
Wear indicator grooves “1” almost disap-
peared



Replace the brake pads as a set.

Refer to “REAR BRAKE” on page 4-24.

EAM30478

CHECKING THE FRONT BRAKE HOSE

1. Check:

•

Brake hose
Cracks/damage/wear



Replace.

2. Check:

•

Brake hose clamp
Loose connection



Tighten the clamp bolt.

3. Stand the vehicle upright and apply the front

brake several times.

4. Check:

•

Brake hose
Brake fluid leaks



Replace the damaged

brake hose.
Refer to “FRONT BRAKE” on page 4-13.

EAM30498

CHECKING THE REAR BRAKE HOSE

1. Check:

•

Brake hose
Cracks/damage/wear



Replace.

2. Check:

•

Brake hose holder

Specified brake fluid

DOT 4

A. Front brake
B. Rear brake

Содержание YZ 2023 Series



























































































































































































































































































































































































Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды

Yamaha YZ 2023 Series, Руководство по эксплуатации для владельца

Результаты поиска

Содержание YZ 2023 Series

Отзывы:

Похожие инструкции для YZ 2023 Series

Бренды по названию

Популярные бренды