Yamaha F15D Скачать руководство пользователя | Manualshive

Страница: 14 / 92

background image

General information

9

dry rags.

●

Do not overfill the fuel tank.

●

Tighten the filler cap securely after re-
fueling.

●

If you should swallow some gasoline,
inhale a lot of gasoline vapor, or get
gasoline in your eyes, get immediate
medical attention.

●

If any gasoline spills onto your skin, im-
mediately wash with soap and water.
Change clothing if gasoline spills on it.

●

Touch the fuel nozzle to the filler open-
ing or funnel to help prevent electro-

static sparks.

CAUTION:

ECM00010

Use only new clean gasoline which has
been stored in clean containers and is not
contaminated with water or foreign mat-

ter.

EMU25570

Gasoline

If knocking or pinging occurs, use a different
brand of gasoline or premium unleaded fuel.

Gasohol

There are two types of gasohol: gasohol con-
taining ethanol and that containing metha-
nol. Gasohol containing ethanol can be used
if ethanol content does not exceed 10% and
the fuel meets minimum octane ratings.
Yamaha does not recommended gasohol
containing methanol because it can cause
fuel system damage or engine performance
problems.

EMU25680

Engine oil

CAUTION:

ECM01050

All 4-stroke engines are shipped from the

factory without engine oil.

EMU25690

Battery requirement

CAUTION:

ECM01060

Do not use a battery that does not meet
the specified capacity. If a battery which
does not meet specifications is used, the

Recommended gasoline:

Regular unleaded gasoline with a min-
imum octane rating of 86 (Pump Oc-
tane Number) = (R+M)/2

Recommended engine oil:

4-stroke motor oil with a combination
of corresponding SAE and API as
shown in the chart

Engine oil quantity (excluding oil filter):

1.0 L (1.06 US qt) (0.88 Imp.qt)

ZMU01710

«
...
12
13
14
15
16
...
»

Содержание F15D





























































































Отзывы:

Нет отзывов

Похожие инструкции для F15D

Бренд: Abit Страницы: 112

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 24

EZ-USB HX2LP CY4605

Бренд: Cypress Страницы: 2

Бренд: Zotac Страницы: 56

Бренд: DFI Страницы: 67

Бренд: AMPTRON Страницы: 16

Бренд: Fujitsu Siemens Computers Страницы: 42

Бренд: Gigabyte Страницы: 120

Бренд: Quick Страницы: 32

Бренд: JETWAY Страницы: 38

Venus VNS563-4GD

Бренд: Diamond Systems Страницы: 43

Бренд: ST Страницы: 22

Бренд: A-Trend Страницы: 60

Motherboard DJ800

Бренд: IWILL Страницы: 52

Бренд: JETWAY Страницы: 39

XILINX SPARTAN-7

Бренд: QMTECH Страницы: 15

Бренд: Gigabyte Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды