Yamaha F15D Скачать руководство пользователя | Manualshive

Страница: 43 / 92

background image

Operation

38

ping the engine immediately after operating
at high speed is not recommended.

EMU27844

Procedure

1.

Push and hold the engine stop button or
turn the main switch to “

” (off).

2.

After stopping the engine, disconnect
the fuel line if there is a fuel joint on the
outboard motor.

3.

Tighten the air vent screw on the fuel
tank cap (if equipped).

4.

Remove the key if the boat will be left
unattended.

NOTE:

The engine can also be stopped by pulling
the lanyard and removing the lock plate from
the engine stop switch, then turning the main

switch to “

” (off).

EMU27861

Trimming outboard motor

The trim angle of the outboard motor helps
determine the position of the bow of the boat
in the water. Correct trim angle will help im-
prove performance and fuel economy while
reducing strain on the engine. Correct trim
angle depends upon the combination of
boat, engine, and propeller. Correct trim is
also affected by variables such as the load in
the boat, sea conditions, and running speed.

WARNING

EWM00740

Excessive trim for the operating condi-
tions (either trim up or trim down) can
cause boat instability and can make
steering the boat more difficult. This in-
creases the possibility of an accident. If
the boat begins to feel unstable or is hard
to steer, slow down and/or readjust the

trim angle.

ZMU02083

ZMU02042

ZMU02041

«
...
41
42
43
44
45
...
»

Содержание F15D





























































































Отзывы:

Нет отзывов

Похожие инструкции для F15D

Бренд: Panasonic Страницы: 35

Бренд: Intel Страницы: 48

Бренд: Lantronix Страницы: 8

Бренд: Texas Instruments Страницы: 8

ISL70219ASEHEV1Z

Бренд: Intersil Страницы: 10

Бренд: Abit Страницы: 48

Бренд: RAK Страницы: 17

EmbCore ROM-7421

Бренд: Advantech Страницы: 25

TB360-BTC PRO 2.0

Бренд: Biostar Страницы: 59

Бренд: EVGA Страницы: 2

Бренд: PRIZM Страницы: 9

STEVAL-PLC001V1

Бренд: ST Страницы: 42

Бренд: Biostar Страницы: 118

Бренд: MSI Страницы: 73

Бренд: California Eastern Laboratories Страницы: 34

Бренд: Advantech Страницы: 98

Бренд: JETWAY Страницы: 48

Бренд: TYAN Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды