Yamaha F15D страница 74 Скачать руководство пользователя

Страница: 74 / 92

Maintenance

the gear oil drain screw hole.

When the oil begins to flow out of the oil
level plug hole, insert and tighten the oil
level plug.

Insert and tighten the gear oil drain
screw.

EMU29302

Cleaning fuel tank

WARNING

EWM00920

Gasoline is highly flammable, and its va-
pors are flammable and explosive.

●

If you have any question about properly
doing this procedure, consult your
Yamaha dealer.

●

Keep away from sparks, cigarettes,
flames, or other sources of ignition
when cleaning the fuel tank.

●

Remove the fuel tank from the boat be-
fore cleaning it. Work only outdoors in
an area with good ventilation.

●

Wipe up any spilled fuel immediately.

●

Reassemble the fuel tank carefully. Im-
proper assembly can result in a fuel
leak, which could result in a fire or ex-
plosion hazard.

●

Dispose of old gasoline according to lo-

cal regulations.

Empty the fuel tank into an approved
container.

Pour a small amount of suitable solvent
into the tank. Install the cap and shake
the tank. Drain the solvent completely.

Remove the screws holding the fuel joint
assembly. Pull the assembly out of the
tank.

Clean the filter (located on the end of the

Recommended gear oil:

Hypoid gear oil SAE#90

Gear oil quantity:

F15EH 250.0 cm

(8.45 US oz) (8.82

Imp.oz)
F15MH 250.0 cm

(8.45 US oz) (8.82

Imp.oz)
F15PH 250.0 cm

(8.45 US oz) (8.82

Imp.oz)
F15PR 250.0 cm

(8.45 US oz) (8.82

Imp.oz)
F9.9ER 250.0 cm

(8.45 US oz) (8.82

Imp.oz)
F9.9MH 250.0 cm

(8.45 US oz) (8.82

Imp.oz)
T9.9EH 370.0 cm

(12.51 US oz)

(13.05 Imp.oz)
T9.9ER 370.0 cm

(12.51 US oz)

(13.05 Imp.oz)

ZMU02065

ZMU02066

Содержание F15D





























































































Результаты поиска

Содержание F15D

Отзывы:

Похожие инструкции для F15D

Бренды по названию

Популярные бренды

Yamaha F15D, Руководство пользователя

Результаты поиска

Содержание F15D

Отзывы:

Похожие инструкции для F15D

Бренды по названию

Популярные бренды