Yamaha F15D Скачать руководство пользователя | Manualshive

Страница: 38 / 92

background image

Operation

33

●

If the choke knob is left in the “

”

(start) position while the engine is running,

the engine will run poorly or stall.

5.

Push the starter button to start the mo-
tor. (Repeat if necessary.)

6.

Immediately after the engine starts, re-
lease the starter button to allow it to re-
turn to its original position.

7.

Slowly return the throttle grip to the fully
closed position so that the engine does
not stall.

CAUTION:

ECM00160

●

Never push the starter button while the
engine is running.

●

Do not keep the starter motor turning
for more than 5 seconds. If the starter
motor is turned continuously for more
than 5 seconds, the battery will be
quickly discharged, thus making it im-
possible to start the engine. The starter
can also be damaged. If the engine will
not start after 5 seconds of cranking,
release the starter button, wait 10 sec-

onds, then crank the engine again.

NOTE:

●

When the engine is cold, it needs to be
warmed up. For further information, see
page 35.

●

If the engine does not start on the first try,

repeat the procedure. If the engine fails to
start after 4 or 5 tries, open the throttle a
small amount (between 1/8 and 1/4) and
try again. Also if the engine is warm and
fails to start, open the throttle a same
amount and try to start the engine again. If

the engine still fails to start, see page 73.

EMU27642

Electric start / remote control models

1.

Place the remote control lever in neutral.

NOTE:

The start-in-gear protection device prevents
the engine from starting except when in neu-

tral.

2.

Attach the engine stop switch lanyard to
a secure place on your clothing, or your
arm or leg. Then install the lock plate on
the other end of the lanyard into the en-
gine stop switch.

WARNING

EWM00120

●

Attach the engine stop switch lanyard
to a secure place on your clothing, or
your arm or leg while operating.

●

Do not attach the lanyard to clothing
that could tear loose. Do not route the
lanyard where it could become entan-
gled, preventing it from functioning.

●

Avoid accidentally pulling the lanyard
during normal operation. Loss of en-

ZMU04880

«
...
36
37
38
39
40
...
»

Содержание F15D





























































































Отзывы:

Нет отзывов

Похожие инструкции для F15D

SBC81206 Series

Бренд: AXIOMTEK Страницы: 74

B360 GAMING PLUS

Бренд: MSI Страницы: 112

Бренд: Supero Страницы: 86

661FX7MJ Series

Бренд: Foxconn Страницы: 81

TPS61090EVM-029

Бренд: Texas Instruments Страницы: 19

Бренд: MAX power Страницы: 20

Бренд: TYAN Страницы: 63

Бренд: Texas Instruments Страницы: 15

Бренд: Parker Страницы: 56

Бренд: MINN KOTA Страницы: 16

Бренд: Supero Страницы: 77

Бренд: Supermicro Страницы: 147

Бренд: Atmel Страницы: 39

Бренд: Gigabyte Страницы: 37

Бренд: Javad Страницы: 12

Бренд: BCM Advanced Research Страницы: 9

Бренд: Golden Motor Страницы: 22

P67 PROFESSIONAL

Бренд: ASROCK Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды