manualshive.com logo in svg

Yamaha F15D, Руководство пользователя

Поделиться
Скачать
Yamaha F15D Скачать руководство пользователя страница 39

 

Operation

 

34

 

gine power means the loss of most
steering control. Also, without engine
power, the boat could slow rapidly. This
could cause people and objects in the

 

boat to be thrown forward.

 

3.

Turn the main switch to “

” (on).

4.

Open the throttle slightly without shifting
using the neutral throttle lever or free ac-
celerator. You may need to change the
throttle opening slightly depending on
engine temperature. After the engine
starts, return the throttle to the original
position.

NOTE:

 

●

 

On remote controls equipped with a neu-
tral throttle lever, a good starting point is to
lift the lever just until you feel resistance,
then lift slightly more.

 

●

 

The neutral throttle lever or free accelera-
tor can only be used when the remote con-

 

trol lever is in neutral.

5.

Press in and hold the main switch to op-
erate the remote choke system. The re-
mote choke switch automatically returns
to its normal position when you release
your hand. Therefore keep the switch
pressed in.

NOTE:

 

●

 

It is not necessary to use the choke when
starting a warm engine.

 

●

 

Push in the main switch fully, or the remote

 

choke system will not operate.

OFF

ON

ZMU01880

N

ZMU02314

START

OFF

ON

ZMU02315

Содержание F15D





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды