Yamaha F15D страница 55 Скачать руководство пользователя | Manualshive

Страница: 55 / 92

background image

Maintenance

50

F15MH 2.08 (27/13)
F15PH 2.08 (27/13)
F15PR 2.08 (27/13)
F9.9ER 2.08 (27/13)
F9.9MH 2.08 (27/13)
T9.9EH 2.92 (38/13)
T9.9ER 2.92 (38/13)

Trim and tilt system:

F15EH Manual tilt
F15MH Manual tilt
F15PH Power tilt
F15PR Power tilt
F9.9ER Manual tilt
F9.9MH Manual tilt
T9.9EH Manual tilt
T9.9ER Manual tilt

Propeller mark:

F15EH J
F15MH J
F15PH J
F15PR J
F9.9ER J
F9.9MH J
T9.9EH R
T9.9ER R

Fuel and oil:

Recommended fuel:

Regular unleaded gasoline

Min. pump octane:

86

Recommended engine oil:

4-stroke outboard motor oil

Engine oil grade API:

API SE, SF, SG, SH, SJ

Engine oil type SAE:

SAE10W30 or SAE10W40

Lubrication:

Wet sump

Engine oil quantity (excluding oil filter):

1.0 L (1.06 US qt) (0.88 Imp.qt)

Recommended gear oil:

Hypoid gear oil SAE#90

Gear oil quantity:

F15EH 250.0 cm

3

(8.45 US oz) (8.82

Imp.oz)
F15MH 250.0 cm

3

(8.45 US oz) (8.82

Imp.oz)
F15PH 250.0 cm

3

(8.45 US oz) (8.82

Imp.oz)
F15PR 250.0 cm

3

(8.45 US oz) (8.82

Imp.oz)
F9.9ER 250.0 cm

3

(8.45 US oz) (8.82

Imp.oz)
F9.9MH 250.0 cm

3

(8.45 US oz)

(8.82 Imp.oz)
T9.9EH 370.0 cm

3

(12.51 US oz)

(13.05 Imp.oz)
T9.9ER 370.0 cm

3

(12.51 US oz)

(13.05 Imp.oz)

Tightening torque for engine:

Spark plug:

18.0 Nm (13.3 ft-lb) (1.84 kgf-m)

Propeller nut:

F15EH 17.0 Nm (12.5 ft-lb) (1.73
kgf-m)
F15MH 17.0 Nm (12.5 ft-lb) (1.73
kgf-m)
F15PH 17.0 Nm (12.5 ft-lb) (1.73
kgf-m)
F15PR 17.0 Nm (12.5 ft-lb) (1.73
kgf-m)
F9.9ER 17.0 Nm (12.5 ft-lb) (1.73
kgf-m)
F9.9MH 17.0 Nm (12.5 ft-lb) (1.73
kgf-m)
T9.9EH 21.0 Nm (15.5 ft-lb) (2.14
kgf-m)
T9.9ER 21.0 Nm (15.5 ft-lb) (2.14
kgf-m)

Engine oil drain bolt:

28.0 Nm (20.7 ft-lb) (2.86 kgf-m)

Engine oil filter:

«
...
53
54
55
56
57
...
»

Содержание F15D





























































































Отзывы:

Нет отзывов

Похожие инструкции для F15D

Бренд: Intel Страницы: 80

Бренд: CIRCUIT DESIGN Страницы: 9

Бренд: Texas Instruments Страницы: 22

Бренд: Gigabyte Страницы: 58

cpuModules CME34BT

Бренд: rtd Страницы: 110

CrossLink LIF-MD6000 Master Link Board - Revision C

Бренд: Lattice Страницы: 40

Бренд: EVGA Страницы: 1

Бренд: Parker Страницы: 56

Бренд: DFI Страницы: 46

Coccinella Master Plus

Бренд: SEA Страницы: 2

Бренд: Texas Instruments Страницы: 20

Spacewalker AV40

Бренд: Shuttle Страницы: 81

Бренд: Portwell Страницы: 9

Бренд: Norco Страницы: 55

Бренд: MSI Страницы: 78

Бренд: DFI Страницы: 79

Бренд: Foxconn Страницы: 115

LanParty DK P35 series

Бренд: DFI Страницы: 126

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды