manualshive.com logo in svg

Yamaha F15D, Руководство пользователя

Поделиться
Скачать
Yamaha F15D Скачать руководство пользователя страница 83

 

Trouble Recovery

 

78

 

starter mechanism or top cowling after
the engine is running.

 

●

 

Do not touch the ignition coil, spark
plug wire, spark plug cap, or other elec-
trical components when starting or op-
erating the motor. You could get an

 

electrical shock.

 

EMU29602

 

Emergency starting engine

 

1.

Remove the top cowling.

2.

Remove the cable by pulling out it from
the starter, if the cable is equipped.

3.

Remove both ends of the choke link rod.

4.

Remove the starter/flywheel cover after
removing the 3 bolts. Disconnect the
wire leads from the starter/flywheel cov-
er.

5.

Prepare the engine for starting. For fur-
ther information, see page 30. Be sure
the engine is in neutral and that the en-
gine stop switch lanyard lock plate is at-
tached to the engine stop switch.

6.

Pull up the lever on the carburetor to op-
erate the choke system when the engine
is cold. After the engine starts, return the
lever to the original position.

 

1. Start-in-gear protection cable

1. Choke link rod

ZMU02069

1

ZMU02332
  

1

ZMU02070

ZMU02026

ZMU02334

Содержание F15D





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды