manualshive.com logo in svg

Yamaha F15D, Руководство пользователя

Поделиться
Скачать
Yamaha F15D Скачать руководство пользователя страница 75

 

Maintenance

 

70

 

suction pipe) in a suitable cleaning sol-
vent. Allow the filter to dry.

5.

Replace the gasket with a new one. Re-
install the fuel joint assembly and tighten
the screws firmly.

 

EMU29312

 

Inspecting and replacing anode(s)

 

Yamaha outboard motors are protected from
corrosion by sacrificial anodes. Inspect the
external anodes periodically. Remove scales
from the surfaces of the anodes. Consult a
Yamaha dealer for replacement of external
anodes.

CAUTION:

 

ECM00720 

 

Do not paint anodes, as this would render

 

them ineffective.

NOTE:

 

Inspect ground leads attached to external
anodes on equipped models. Consult a
Yamaha dealer for inspection and replace-
ment of internal anodes attached to the pow-

 

er unit.

 

EMU29320

 

Checking battery (for electric start 
models)

WARNING

 

EWM00330 

 

Battery electrolytic fluid is dangerous; it
contains sulfuric acid and therefore is
poisonous and highly caustic.
Always follow these preventive mea-
sures:

 

●

 

Avoid bodily contact with electrolytic
fluid as it can cause severe burns or
permanent eye injury.

 

●

 

Wear protective eye gear when han-
dling or working near batteries.

Antidote (EXTERNAL):

 

●

 

SKIN - Flush with water.

 

●

 

EYES - Flush with water for 15 minutes
and get immediate medical attention.

Antidote (INTERNAL):

 

●

 

Drink large quantities of water or milk

ZMU02067

ZMU02924

Содержание F15D





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды