Yamaha F15D Скачать руководство пользователя | Manualshive

Страница: 56 / 92

background image

Maintenance

51

18.0 Nm (13.3 ft-lb) (1.84 kgf-m)

EMU28222

Transporting and storing

outboard motor

WARNING

EWM00690

●

Leaking fuel is a fire hazard. When
transporting and storing the outboard
motor, close the air vent screw and fuel
cock to prevent fuel from leaking.

●

USE CARE when transporting fuel tank,
whether in a boat or car.

●

DO NOT fill fuel container to maximum
capacity. Gasoline will expand consid-
erably as it warms up and can build up
pressure in the fuel container. This can
cause fuel leakage and a potential fire

hazard.

WARNING

EWM00700

Never get under the lower unit while it is
tilted, even if a motor support bar is used.
Severe injury could occur if the outboard

motor accidentally falls.

CAUTION:

ECM00660

Do not use the tilt support lever or knob
when trailering the boat. The outboard
motor could shake loose from the tilt sup-
port and fall. If the motor cannot be trail-
ered in the normal running position, use
an additional support device to secure it

in the tilt position.

The outboard motor should be trailered and
stored in the normal running position. If there
is insufficient road clearance in this position,
then trailer the outboard motor in the tilt po-
sition using a motor support device such as
a transom saver bar. Consult your Yamaha
dealer for further details.

EMU28235

Clamp screw mounting models

When transporting or storing the outboard
motor while removed from a boat, keep the
outboard motor in the attitude shown.

NOTE:

Place a towel or something similar under the

outboard motor to protect it from damage.

EMU28241

Storing outboard motor

When storing your Yamaha outboard motor
for prolonged periods of time (2 months or
longer), several important procedures must
be performed to prevent excessive damage.
It is advisable to have your outboard motor
serviced by an authorized Yamaha dealer
prior to storage. However, you, the owner,
with a minimum of tools, can perform the fol-

ZMU02049

ZMU02050

«
...
54
55
56
57
58
...
»

Содержание F15D





























































































Отзывы:

Нет отзывов

Похожие инструкции для F15D

Бренд: Rabbit Страницы: 144

Virtex-II Pro ML300

Бренд: Xilinx Страницы: 17

Бренд: Gigabyte Страницы: 125

Бренд: PC Partner Страницы: 20

Бренд: Biostar Страницы: 65

Бренд: MSI Страницы: 92

Бренд: IBASE Technology Страницы: 91

DQ45CB - Desktop Board Executive Series Motherboard

Бренд: Intel Страницы: 96

HBJC390F841VAG34B

Бренд: JETWAY Страницы: 44

Бренд: ECS Страницы: 61

Fatal1ty B150 Gaming K4

Бренд: ASROCK Страницы: 154

Бренд: Safran Страницы: 29

Бренд: NXP Semiconductors Страницы: 28

Бренд: Advantech Страницы: 136

Бренд: ECS Страницы: 131

Бренд: TYAN Страницы: 70

Бренд: Sunny Giken Страницы: 123

Бренд: Intel Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды