manualshive.com logo in svg

Yamaha F15D, Руководство пользователя

Поделиться
Скачать
Yamaha F15D Скачать руководство пользователя страница 4

 

Table of contents

 

General information .......................... 1

 

Identification numbers record ..........  1

 

Outboard motor serial number .......... 1
Key number....................................... 1

 

Emission control information ...........  1

 

North American models..................... 1
Star labels ......................................... 2

 

Safety information ...........................  3
Important labels...............................  4

 

Warning labels .................................. 4
Caution labels ................................... 5

 

Basic boating rules (Rules of the 

road) .............................................. 5

 

Steering and sailing rules and 

sound signals.................................. 5

Rules when encountering vessels .... 6
Other special situations..................... 7

 

Fueling instructions .........................  8

 

Gasoline ............................................ 9
Engine oil .......................................... 9

 

Battery requirement.........................  9

 

Battery specifications ...................... 10
Without a rectifier or Rectifier 

Regulator ...................................... 10

 

Propeller selection.........................  10
Start-in-gear protection .................  11

 

Basic components .......................... 12

 

Main components ..........................  12

 

Fuel tank ......................................... 13
Fuel joint ......................................... 14
Fuel gauge ...................................... 14
Fuel tank cap .................................. 14
Air vent screw ................................. 14
Remote control................................ 14
Remote control lever ....................... 14
Neutral interlock trigger ................... 15
Neutral throttle lever........................ 15
Choke switch................................... 15
Tiller handle .................................... 15
Gear shift lever................................ 16
Throttle grip ..................................... 16
Throttle indicator ............................. 16
Throttle friction adjuster................... 17
Engine stop lanyard switch ............. 17
Engine stop button .......................... 18

Choke knob for pull type ................. 18
Manual starter handle ..................... 18
Starter button .................................. 19
Main switch ..................................... 19
Power tilt switch .............................. 19
Steering friction adjuster ................. 20
Steering friction adjuster ................. 20
Trim tab with anode......................... 20
Trim rod (tilt pin) .............................. 21
Tilt lock mechanism......................... 21
Tilt support knob.............................. 21
Tilt support bar ................................ 21
Power tilt unit................................... 22
Top cowling lock lever(s) (turn 

type) .............................................. 22

Flushing device ............................... 22
Warning indicator ............................ 22

 

Warning system ............................  23

 

Overheat warning ............................ 23
Low oil pressure warning ................ 23

 

Operation ......................................... 25

 

Installation.....................................  25

 

Mounting the outboard motor .......... 25
Clamping the outboard motor.......... 26

 

Breaking in engine ........................  27

 

Procedure for 4-stroke models ........ 27

 

Preoperation checks .....................  27

 

Fuel ................................................. 27
Controls ........................................... 27
Engine ............................................. 28
Checking the engine oil level .......... 28

 

Filling fuel......................................  28

 

Ring Free Fuel Additive................... 28

 

Operating engine ..........................  29

 

Feeding fuel (portable tank) ............ 29
Starting engine ................................ 30

 

Warming up engine.......................  35

 

Manual start and electric start 

models .......................................... 35

 

Shifting ..........................................  35

 

Forward (tiller handle and remote 

control models) ............................. 36

Reverse (manual tilt and hydro tilt 

models) ......................................... 36

 

Stopping engine ............................  37

Содержание F15D





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды