manualshive.com logo in svg

Yamaha F15D, Руководство пользователя

Поделиться
Скачать
Yamaha F15D Скачать руководство пользователя страница 46

 

Operation

 

41

 

Bow Down

 

Too much trim-in causes the boat to “plow”
through the water, decreasing fuel economy
and making it hard to increase speed. Oper-
ating with excessive trim-in at higher speeds
also makes the boat unstable. Resistance at
the bow is greatly increased, heightening the
danger of “bow steering” and making opera-
tion difficult and dangerous.

NOTE:

 

Depending on the type of boat, the outboard
motor trim angle may have little effect on the

 

trim of the boat when operating.

 

EMU27933

 

Tilting up and down

 

If the engine will be stopped for some time or
if the boat is moored in shallows, the out-
board motor should be tilted up to protect the
propeller and casing from damage by colli-
sion with obstructions, and also to reduce

salt corrosion.

WARNING

 

EWM00220 

 

Be sure all people are clear of the out-
board motor when tilting up and down,
also be careful not to pinch any body
parts between the drive unit and engine

 

bracket.

WARNING

 

EWM00250 

 

Leaking fuel is a fire hazard. If there is a
fuel joint on the outboard motor, discon-
nect the fuel line or close the fuel cock if
the engine will be tilted for more than a

 

few minutes. Otherwise fuel may leak.

CAUTION:

 

ECM00241 

 

●

 

Before tilting the outboard motor, stop
the engine by following the procedure
on page 37. Never tilt the outboard mo-
tor while the engine is running. Severe
damage from overheating can result.

 

●

 

Do not tilt up the engine by pushing the
tiller handle (if equipped) because this

 

could break the handle.

 

EMU27976

 

Procedure for tilting up (manual tilt 
models)

 

1.

Place the gear shift lever in neutral.

ZMU01988

N

Содержание F15D





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды