Yamaha F15D Скачать руководство пользователя | Manualshive

Страница: 66 / 92

background image

Maintenance

61

sources of ignition.

WARNING

EWM00910

Leaking fuel can result in fire or explo-
sion.

●

Check for fuel leakage regularly.

●

If any fuel leakage is found, the fuel
system must be repaired by a qualified
mechanic. Improper repairs can make

the outboard unsafe to operate.

Check the fuel lines for leaks, crack, or mal-
function. If a problem is found, your Yamaha
dealer or other qualified mechanic should re-
pair it immediately.

Checkpoints

●

Fuel system parts leakage

●

Fuel line joint leakage

●

Fuel line cracks or other damage

●

Fuel connector leakage

EMU28980

Inspecting fuel filter

WARNING

EWM00310

Gasoline is highly flammable, and its va-
pors are flammable and explosive.

●

If you have any question about properly
doing this procedure, consult your
Yamaha dealer.

●

Do not perform this procedure on a hot
or running engine. Allow the engine to
cool.

●

There will be fuel in the fuel filter. Keep
away from sparks, cigarettes, flames or
other sources of ignition.

●

This procedure will allow some fuel to
spill. Catch fuel in a rag. Wipe up any
spilled fuel immediately.

●

The fuel filter must be reassembled
carefully with the O-ring, filter cup, and
hoses in place. Improper assembly or
replacement could result in a fuel leak,
which could result in a fire or explosion

hazard.

EMU29001

Cleaning fuel filter

1.

Remove the nut holding the fuel filter as-
sembly if equipped.

ZMU05010

1. Nut

ZMU02055

1

«
...
64
65
66
67
68
...
»

Содержание F15D





























































































Отзывы:

Нет отзывов

Похожие инструкции для F15D

Бренд: Xilinx Страницы: 23

Бренд: Xilinx Страницы: 60

Бренд: Xilinx Страницы: 41

Zynq UltraScale+ ZCU104

Бренд: Xilinx Страницы: 92

Zynq UltraScale+ ZCU104

Бренд: Xilinx Страницы: 4

Spartan-3A DSP FPGA Series

Бренд: Xilinx Страницы: 10

Бренд: Xilinx Страницы: 92

Бренд: Datavan Страницы: 15

Бренд: Alcad Страницы: 98

Бренд: JETWAY Страницы: 44

Бренд: ablelogic Страницы: 47

970 Extreme3 R2.0

Бренд: ASROCK Страницы: 70

Бренд: Texas Instruments Страницы: 25

Бренд: Advantech Страницы: 118

Spacewalker AK32

Бренд: Shuttle Страницы: 89

DLP LightCrafter Display 3310

Бренд: Texas Instruments Страницы: 16

Бренд: Merit Страницы: 4

EVAL-IH-R5IPB-A-V1

Бренд: Infineon Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды