Yamaha F15D страница 71 Скачать руководство пользователя

Страница: 71 / 92

Maintenance

Checkpoints

●

Check each of the propeller blades for
wear, erosion from cavitation or ventila-
tion, or other damage.

●

Check the propeller shaft for damage.

●

Check the splines / shear pin for wear or
damage.

●

Check for fish line tangled around the pro-
peller shaft.

●

Check the propeller shaft oil seal for dam-
age.

NOTE:

If the shear pin equipped: it is designed to
break if the propeller hits a hard underwater
obstacle to help protect the propeller and
drive mechanism. The propeller will then
spin freely on the shaft. If this happens, the

shear pin must be replaced.

EMU30660

Removing the propeller

EMU29194

Spline models

Straighten the cotter pin and pull it out
using a pair of pliers.

Remove the propeller nut, washer, and
spacer (if equipped).

Remove the propeller and thrust wash-
er.

EMU29212

Dual thrust models

Straighten the cotter pin and pull it out
using a pair of pliers.

ZMU02059

ZMU01897

1. Cotter pin
2. Propeller nut
3. Washer
4. Propeller
5. Thrust washer

ZMU02062

Содержание F15D





























































































Результаты поиска

Содержание F15D

Отзывы:

Похожие инструкции для F15D

Бренды по названию

Популярные бренды

Yamaha F15D, Руководство пользователя

Результаты поиска

Содержание F15D

Отзывы:

Похожие инструкции для F15D

Бренды по названию

Популярные бренды