Yamaha F15D Скачать руководство пользователя

Страница: 28 / 92

Basic components

EMU26801

Warning system

CAUTION:

ECM00090

Do not continue to operate the engine if a
warning device has activated. Consult
your Yamaha dealer if the problem can-

not be located and corrected.

EMU26813

Overheat warning

This engine has an overheat warning device.
If the engine temperature rises too high, the
warning device will activate.

Activation of warning device

●

The engine speed will automatically de-
crease to about 2000 r/min.

●

The overheat warning indicator will light (if
equipped on the bottom cowling or the ta-
chometer).

●

The buzzer will sound (if equipped on the
tiller handle, remote control box, or main
switch panel).

If the warning system has activated, stop the
engine and check the cooling water inlet for
clogging.

EMU30164

Low oil pressure warning

If the oil pressure drops too low, the warning
device will activate.
Activation of warning device

●

The engine speed will automatically de-
crease to about 2000 r/min.

●

The low oil pressure warning indicator will
light.

ZMU02010

ZMU03026

Содержание F15D





























































































Результаты поиска

Содержание F15D

Отзывы:

Похожие инструкции для F15D

Бренды по названию

Популярные бренды

Yamaha F15D, Руководство пользователя

Результаты поиска

Содержание F15D

Отзывы:

Похожие инструкции для F15D

Бренды по названию

Популярные бренды