Yamaha F15D Скачать руководство пользователя

Страница: 49 / 92

Operation

from marine growth and corrosion which
could damage the power trim and tilt

mechanism.

EMU30190

Procedure for tilting down (manual
tilt models)

Place the tilt lock lever in the lock posi-
tion.

Slightly tilt the engine up until the tilt sup-
port bar is automatically released.

Slowly tilt the engine down.

EMU28053

Procedure for tilting down

Power trim and tilt models / power tilt models
1.

Push the power tilt / power trim and tilt
switch “

” (up) until the outboard motor

is supported by the tilt rod and the tilt
support lever / tilt support knob becomes
free.

Release the tilt support lever or pull out
the tilt support knob.

Push the power tilt / power trim and tilt
switch “

” (down) to lower the outboard

motor to the desired position.

EMU28060

Cruising in shallow water

The outboard motor can be tilted up partially
to allow operation in shallow water.

ZMU02048

ZMU04886

ZMU01936

ZMU02826

ZMU04901

Содержание F15D





























































































Результаты поиска

Содержание F15D

Отзывы:

Похожие инструкции для F15D

Бренды по названию

Популярные бренды

Yamaha F15D, Руководство пользователя

Результаты поиска

Содержание F15D

Отзывы:

Похожие инструкции для F15D

Бренды по названию

Популярные бренды