manualshive.com logo in svg

Yamaha F15D, Руководство пользователя

Поделиться
Скачать
Yamaha F15D Скачать руководство пользователя страница 45

 

Operation

 

40

 

only when the boat is at a complete

 

stop with the engine off.

 

Tilt the engine to the desired angle using the
power tilt switch.

NOTE:

 

Stay within the trim operating angle when
trimming the outboard motor using the power

 

tilt system.

To raise the bow (“trim-out”), tilt the engine

up.
To lower the bow (“trim-in”), tilt the engine
down.
Make test runs with the trim set to different
angles to find the position that works best for
your boat and operating conditions.

 

EMU27911

 

Adjusting boat trim

 

When the boat is on plane, a bow-up attitude
results in less drag, greater stability and effi-
ciency. This is generally when the keel line of
the boat is up about 3 to 5 degrees. With the
bow up, the boat may have a greater tenden-
cy to steer to one side or the other. Compen-
sate for this as you steer. The trim tab can
also be adjusted to help offset this effect.
When the bow of the boat is down, it is easier
to accelerate from a standing start onto
plane.

 

Bow Up

 

Too much trim-out puts the bow of the boat
too high in the water. Performance and econ-
omy are decreased because the hull of the
boat is pushing the water and there is more
air drag. Excessive trim-out can also cause
the propeller to ventilate, which reduces per-
formance further, and the boat may “por-
poise” (hop in the water), which could throw
the operator and passengers overboard.

ZMU02811

UP

DN

DN

UP

ZMU04899

Содержание F15D





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды