Yamaha F15D Скачать руководство пользователя

Страница: 26 / 92

Basic components

starboard side “B” in the figure.

CAUTION:

ECM00840

The trim tab also serves as an anode to
protect the engine from electrochemical
corrosion. Never paint the trim tab as it

will become ineffective as an anode.

EMU26261

Trim rod (tilt pin)

The position of the trim rod determines the
minimum trim angle of the outboard motor in
relation to the transom.

EMU26312

Tilt lock mechanism

The tilt lock mechanism is used to prevent
the outboard motor from lifting out of the wa-
ter when in reverse gear.

To lock it, set the tilt lock lever in the “

”

(lock) position. To release, push the tilt lock
lever in the “

” (release) position.

EMU26320

Tilt support knob

To keep the outboard motor in the tilted up
position, push the tilt support knob under the
swivel bracket.

EMU26330

Tilt support bar

The tilt support bar keeps the outboard motor
in the tilted up position.

1. Trim tab
2. Bolt

ZMU03097

ZMU02007

1. Tilt lock lever

ZMU02008

ZMU04884

Содержание F15D





























































































Результаты поиска

Содержание F15D

Отзывы:

Похожие инструкции для F15D

Бренды по названию

Популярные бренды

Yamaha F15D, Руководство пользователя

Результаты поиска

Содержание F15D

Отзывы:

Похожие инструкции для F15D

Бренды по названию

Популярные бренды