Yamaha F15D Скачать руководство пользователя | Manualshive

Страница: 78 / 92

background image

73

Trouble Recovery

EMU29422

Troubleshooting

A problem in the fuel, compression, or igni-
tion systems can cause poor starting, loss of
power, or other problems. This section de-
scribes basic checks and possible remedies,
and covers all Yamaha outboard motors.
Therefore some items may not apply to your
model.
If your outboard motor requires repair, bring
it to your Yamaha dealer.
If the engine trouble warning indicator is
flashing, consult your Yamaha dealer.

Starter will not operate.

Q. Is battery capacity weak or low?
A. Check battery condition. Use battery of
recommended capacity.

Q. Are battery connections loose or corrod-
ed?
A. Tighten battery cables and clean battery
terminals.

Q. Is fuse for electric start relay or electric cir-
cuit blown?
A. Check for cause of electric overload and
repair. Replace fuse with one of correct am-
perage.

Q. Are starter components faulty?
A. Have serviced by a Yamaha dealer.

Q. Is shift lever in gear?
A. Shift to neutral.

Engine will not start (starter operates).

Q. Is fuel tank empty?
A. Fill tank with clean, fresh fuel.

Q. Is fuel contaminated or stale?

A. Fill tank with clean, fresh fuel.

Q. Is fuel filter clogged?
A. Clean or replace filter.

Q. Is starting procedure incorrect?
A. See page 30.

Q. Has fuel pump malfunctioned?
A. Have serviced by a Yamaha dealer.

Q. Are spark plug(s) fouled or of incorrect
type?
A. Inspect spark plug(s). Clean or replace
with recommended type.

Q. Are spark plug cap(s) fitted incorrectly?
A. Check and re-fit cap(s).

Q. Is ignition wiring damaged or poorly con-
nected?
A. Check wires for wear or breaks. Tighten
all loose connections. Replace worn or bro-
ken wires.

Q. Are ignition parts faulty?
A. Have serviced by a Yamaha dealer.

Q. Is engine stop switch lanyard not at-
tached?
A. Attach lanyard.

Q. Are engine inner parts damaged?
A. Have serviced by a Yamaha dealer.

Engine idles irregularly or stalls.

Q. Are spark plug(s) fouled or of incorrect
type?
A. Inspect spark plug(s). Clean or replace
with recommended type.

«
...
76
77
78
79
80
...
»

Содержание F15D





























































































Отзывы:

Нет отзывов

Похожие инструкции для F15D

Бренд: u-blox Страницы: 25

Бренд: Avalue Technology Страницы: 12

Бренд: MIPS Страницы: 10

Бренд: Acrosser Technology Страницы: 7

Бренд: JETWAY Страницы: 52

Бренд: NXP Semiconductors Страницы: 269

DS-5116HFI Series

Бренд: HIKVISION Страницы: 22

Advance 10T Series

Бренд: QDI Страницы: 74

A20-OLINUXINO-LIME

Бренд: OLIMEX Страницы: 49

Бренд: Texas Instruments Страницы: 11

Бренд: Magic-Pro Computer Страницы: 40

Бренд: Microchip Technology Страницы: 89

Бренд: IEI Technology Страницы: 198

Бренд: TYAN Страницы: 117

Бренд: bolid Страницы: 32

Бренд: Suzuki Страницы: 320

Minix780G Series

Бренд: J&W Страницы: 41

Бренд: LAPIS Semiconductor Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды