Xilinx Zynq-7000 Скачать руководство пользователя страница 313

Страница: 313 / 678

Zynq-7000 AP SoC and 7 Series FPGAs MIS v4.1

313

UG586 November 30, 2016

www.xilinx.com

Chapter 2:

QDR II+ Memory Interface Solution

user_design/rtl/phy

Table 2-5

lists the files in the

user_design/rtl/phy

directory:

Table 2-4:

Files in user_design/rtl/clocking Directory

Name

(1)

Description

infrastructure.v

This module helps in clock generation and distribution.

clk_ibuf.v

This module instantiates the system clock input buffers.

iodelay_ctrl.v

This module instantiates the IDELAYCTRL primitive needed for IODELAY use.

Notes:

1. All file names are prefixed with the MIG version number. For example, for the MIG 4.1 release module name of

clk_ibuf in generated output is now mig_7series_v4_1_clk_ibuf.

Table 2-5:

Files in user_design/rtl/phy

Name

(1)

Description

qdr_phy_top.v

This is the top-level module for the physical layer.

qdr_phy_write_top.v

This is the top-level wrapper for the write path.

qdr_rld_phy_read_top.v

This is the top-level of the read path.

qdr_rld_mc_phy.v

This module is a parameterizable wrapper instantiating up to

three I/O banks each with 4-lane PHY primitives.

qdr_phy_write_init_sm.v

This module contains the logic for the initialization state machine.

qdr_phy_write_control_io.v

This module contains the logic for the control signals going to the

memory.

qdr_phy_write_data_io.v

This module contains the logic for the data and byte writes going

to the memory.

qdr_rld_prbs_gen.v

This PRBS module uses a many-to-one feedback mechanism for

2n sequence generation.

qdr_rld_phy_ck_addr_cmd_delay.v

This module contains the logic to provide the required delay on

the address and control signals

qdr_rld_phy_rdlvl.v

This module contains the logic for stage 1 calibration.

qdr_rld_phy_read_stage2_cal.v

This module contains the logic for stage 2 calibration.

qdr_rld_phy_read_data_align.v

This module realigns the incoming data.

qdr_rld_phy_read_vld_gen.v

This module contains the logic to generate the valid signal for the

read data returned on the user interface.

qdr_phy_byte_lane_map.v

This wrapper file handles the vector remapping between the

mc_phy module ports and the user memory ports.

qdr_rld_phy_4lanes.v

This module is the parameterizable 4-lane PHY in an I/O bank.

qdr_rld_byte_lane.v

This module contains the primitive instantiations required within

an output or input byte lane.

Send Feedback

Содержание Zynq-7000







































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Zynq-7000

Отзывы:

Похожие инструкции для Zynq-7000

Бренды по названию

Популярные бренды

Xilinx Zynq-7000, Руководство пользователя

Результаты поиска

Содержание Zynq-7000

Отзывы:

Похожие инструкции для Zynq-7000

Бренды по названию

Популярные бренды