Xilinx Zynq-7000 Скачать руководство пользователя страница 623

Страница: 623 / 678

Zynq-7000 AP SoC and 7 Series FPGAs MIS v4.1

623

UG586 November 30, 2016

www.xilinx.com

Chapter 4:

LPDDR2 SDRAM Memory Interface Solution

DQ_WIDTH

This is the memory DQ bus width.

This parameter supports DQ widths

from 8 to a maximum of 72 in

increments of 8. The available

maximum DQ width is frequency

dependent on the selected memory

device.

DQS_WIDTH

This is the memory DQS bus width.

DQ_WIDTH/8

BURST_MODE

This is the memory data burst length.

LPDDR2: “8”

BM_CNT_WIDTH

This is the number of bits required to index a

bank machine and is given by

ceil(log

(nBANK_MACHS)).

ADDR_CMD_MODE

This parameter is used by the controller to

calculate timing on the memory addr/cmd bus.

This parameter should

not

be changed.

“1T”

ORDERING

(3)

This option reorders received requests to

optimize data throughput and latency.

“NORM”: Allows the Memory

Controller to reorder read but not

write commands to the memory.
"RELAXED": Allows the Memory

Controller to reorder commands to

the memory for maximum

efficiency. Strong ordering is not

preserved at the native interface in

this mode.
“STRICT”: Forces the Memory

Controller to execute commands in

the exact order received.

STARVE_LIMIT

This sets the number of times a read request

can lose arbitration before the request declares

itself high priority. The actual number of lost

arbitrations is STARVE_LIMIT

nBANK_MACHS.

1, 2, 3, ... 10

IODELAY_GRP

(4)

This is an ASCII character string to define an

IDELAY group used in a memory design. This is

used by the Vivado tools to group all

instantiated IDELAYs into the same bank.

Unique names must be assigned when multiple

IP cores are implemented on the same FPGA.

Default: “IODELAY_MIG”

PAYLOAD_WIDTH

This is the actual DQ bus used for user data.

PAYLOAD_WIDTH = DATA_WIDTH

DEBUG_PORT

This option enables debug signals/control.

“ON”

“OFF”

TCQ

This is the clock-to-Q delay for simulation

purposes.

(The value is in picoseconds.)

tCK

This is the memory tCK clock period (ps).

The value, in picoseconds, is based

on the selected frequency in the

MIG tool.

DIFF_TERM_SYSCLK

“TRUE,” “FALSE”

Differential termination for system

clock input pins.

Table 4-25:

7 Series FPGA Memory Solution Configuration Parameters

(Cont’d)

Parameter

Description

Options

Send Feedback

Содержание Zynq-7000







































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Zynq-7000

Отзывы:

Похожие инструкции для Zynq-7000

Бренды по названию

Популярные бренды

Xilinx Zynq-7000, Руководство пользователя

Результаты поиска

Содержание Zynq-7000

Отзывы:

Похожие инструкции для Zynq-7000

Бренды по названию

Популярные бренды