Xilinx Zynq-7000 Скачать руководство пользователя страница 436

Страница: 436 / 678

Zynq-7000 AP SoC and 7 Series FPGAs MIS v4.1

436

UG586 November 30, 2016

www.xilinx.com

Chapter 3:

RLDRAM II and RLDRAM 3 Memory Interface Solutions

Table 3-11

lists the signals used in the infrastructure module that provides the necessary

clocks and reset signals required in the design.

Physical Interface

The physical interface is the connection from the FPGA memory interface solution to an

external RLDRAM II/RLDRAM 3 device. The I/O signals for this interface are defined in

Table 3-12

. These signals can be directly connected to the corresponding signals on the

RLDRAM II/RLDRAM 3 device.

Table 3-11:

Infrastructure Clocking and Reset Signals

Signal

Direction

Description

mmcm_clk

Input

System clock input

sys_rst

Input

Core reset from user application

iodelay_ctrl_rdy Input

IDELAYCTRL lock status

clk

Output

Half frequency FPGA logic clock

mem_refclk

Output

PLL output clock at same frequency as the memory clock

freq_refclk

Output

PLL output clock to provide the FREQREFCLK input to the Phaser. The freq_refclk is

generated such that its frequency in the range of 400 MHz–1,066 MHz

sync_pulse

Output

PLL output generated at 1/16 of mem_Refclk and is a synchronization signal sent

to the PHY hard blocks that are used in a multi-bank implementation

pll_locked

Output

Locked output from PLLE2_ADV

rstdiv0

Output

Reset output synchronized to internal FPGA logic half-frequency clock.

rst_phaser_ref

Output

Reset for the Phaser in the Physical Layer.

Table 3-12:

Physical Interface Signals

Signal

Direction

Description

rld_ck_p

Output

System Clock CK. This is the address/command clock to the memory device.

rld_ck_n

Output

System Clock CK#. This is the inverted system clock to the memory device.

rld_dk_p

InOut

Write Clock DK. This is the write clock to the memory device.

rld_dk_n

InOut

Write Clock DK#. This is the inverted write clock to the memory device.

rld_a

Output

Address. This is the address supplied for memory operations.

rld_ba

Output

Bank Address. This is the bank address supplied for memory operations.

rld_cs_n

Output

Chip Select CS#. This is the active-Low chip select control signal for the

memory.

rld_we_n

Output

Write Enable WE#. This is the active-Low write enable control signal for the

memory.

rld_ref_n

Output

Refresh REF#. This is the active-Low refresh control signal for the memory.

rld_dm

Output

Data Mask DM. This is the active-High mask signal, driven by the FPGA to

mask data that a user does not want written to the memory during a write

command.

Send Feedback

Содержание Zynq-7000







































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Zynq-7000

Отзывы:

Похожие инструкции для Zynq-7000

Бренды по названию

Популярные бренды

Xilinx Zynq-7000, Руководство пользователя

Результаты поиска

Содержание Zynq-7000

Отзывы:

Похожие инструкции для Zynq-7000

Бренды по названию

Популярные бренды