Xilinx Zynq-7000 Скачать руководство пользователя страница 213

Страница: 213 / 678

Zynq-7000 AP SoC and 7 Series FPGAs MIS v4.1

213

UG586 November 30, 2016

www.xilinx.com

Chapter 1:

DDR3 and DDR2 SDRAM Memory Interface Solution

Information on Sharing BUFG Clock (phy_clk)

The MIG 7 series DDR3 design includes an MMCM which outputs the

phy_clk

on a BUFG

route. It is not possible to share this clock amongst multiple controllers to synchronize the

user interfaces. This is not allowed because the timing from the FPGA logic to the PHY

Control block must be controlled. This is not possible when the clock is shared amongst

multiple controllers. The only option for synchronizing user interfaces amongst multiple

controllers is to create an asynchronous FIFO for clock domain transfer.

Information on Sync_Pulse

The MIG 7 series DDR3/DDR2 design includes one PLL that generates the necessary design

clocks. One of these outputs is the

sync_pulse

. The sync pulse clock is 1/16 of the

mem_refclk

frequency and must have a duty cycle distortion of 1/16 or 6.25%. This clock

is distributed across the low skew clock backbone and keeps all PHASER_IN/_OUT and

PHY_Control blocks in sync with each other. The signal is sampled by the

mem_refclk

both the PHASER_INs/_OUTs and PHY_Control blocks. The phase, frequency, and duty cycle

of the

sync_pulse

is chosen to provide the greatest setup and hold margin across PVT.

DDR3 Pinout Examples

Table 1-69

shows an example of a 16-bit DDR3 interface contained within one bank. This

example is for a component interface using a 1 Gb x16 part. If x8 components are used or

a higher density part is needed that would require more address pins, these options are

possible:

• An additional bank can be used.
•

RESET_N

can be moved to another bank as long as timing is met. External timing for

this signal is not critical and a level shifter can be used.

• DCI cascade can be used to free up the

VRN

VRP

pins if another bank is available for

the DCI master.

Internal V

REF

is used in this example.

Table 1-69:

16-Bit DDR3 Interface Contained in One Bank

Bank

Signal Name

Byte Group

I/O Type

I/O Number

Special

Designation

VRP

–

DQ15

D_11

–

DQ14

D_10

–

DQ13

D_09

–

DQ12

D_08

–

DQS1_P

D_07

DQS-P

Send Feedback

Содержание Zynq-7000







































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Zynq-7000

Отзывы:

Похожие инструкции для Zynq-7000

Бренды по названию

Популярные бренды

Xilinx Zynq-7000, Руководство пользователя

Результаты поиска

Содержание Zynq-7000

Отзывы:

Похожие инструкции для Zynq-7000

Бренды по названию

Популярные бренды