Xilinx Zynq-7000 Скачать руководство пользователя страница 344

Страница: 344 / 678

Zynq-7000 AP SoC and 7 Series FPGAs MIS v4.1

344

UG586 November 30, 2016

www.xilinx.com

Chapter 2:

QDR II+ Memory Interface Solution

• The maximum electrical delay between any address and control signals and the

corresponding K/K# should be ± 50 ps.

• There is no relation between CQ and the K clocks. K should be matched with D, and CQ

should be matched with Q (read data).

Pinout Requirements

Xilinx 7 series FPGAs are designed for very high-performance memory interfaces, and

certain rules must be followed to use the QDR II+ physical layer. Xilinx 7 series FPGAs have

dedicated logic for each byte group. Four byte groups are available in each 50-pin bank.

Each 50-pin bank consists of four byte groups that contain one DQS Clock capable I/O pair

and ten associated I/Os. Two pairs of Multi-region Clock-capable I/O (MRCC) pins are

available in a bank, and are used for placing the read clocks (CQ and CQ#).

In a typical QDR II+ write bank configuration, 9 of these 10 I/Os are used for the Write data

(D) and one is used for the byte write (BW). The write clocks (K/K#) use one of the DQS pairs

inside the write bank. Within a read bank, the read data are placed on 9 of the 10 I/Os, and

the CQ/CQ# clocks placed in the MRCC_P pins available inside the read bank.

Xilinx 7 series FPGAs have dedicated clock routing for high-speed synchronization that is

routed vertically within the I/O banks. Thus, QDR II+ memory interfaces must be arranged

in the banks vertically and not horizontally. In addition, the maximum height is three banks.

After generating a core through the MIG tool, the most optimal pinout has been selected

for the design. Manual changes through the XDC are not recommended. However, if the

XDC needs to be altered, the following rules must be taken into consideration:

• The write data bus (D) of a memory interface must be placed within a single bank. It is

required to arrange the write data bus byte wise (nine bits wide) among the FPGA byte

groups. All byte write (BW) signals of the interface are required to place in the same

bank.

• K/K# clocks must be kept in the same bank as the write data bank. They should be

placed on a DQS pin pair.

• The read data bus (Q) must be arranged byte wise (nine bits wide) among the FPGA

byte groups. Xilinx recommends keeping the complete read data bus of a memory

component within a single bank.

• The read data clocks (CQ and CQ#) must be placed on the two MRCC_P or MRCC_N pins

available in the same bank as the read data or an adjacent bank to it. Xilinx

recommends keeping the read data and read clocks in the same bank.

• All address/control signals must be placed within a single bank. The address bank

should be placed adjacent to the data write (D) bank.

• The

dll_off_n

signal can be placed on any free I/O available in the banks used for

the memory interface.

Send Feedback

Содержание Zynq-7000







































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Zynq-7000

Отзывы:

Похожие инструкции для Zynq-7000

Бренды по названию

Популярные бренды

Xilinx Zynq-7000, Руководство пользователя

Результаты поиска

Содержание Zynq-7000

Отзывы:

Похожие инструкции для Zynq-7000

Бренды по названию

Популярные бренды