Xilinx Zynq-7000 Скачать руководство пользователя страница 233

Страница: 233 / 678

Zynq-7000 AP SoC and 7 Series FPGAs MIS v4.1

233

UG586 November 30, 2016

www.xilinx.com

Chapter 1:

DDR3 and DDR2 SDRAM Memory Interface Solution

• Check the reset to ensure the polarity is correct and the signal is clean. The reset signal

must be applied for a minimum pulse width of 5 ns.

• Check terminations by using this user guide as a guideline.
• Perform general signal integrity analysis.

IBIS simulations should run to ensure terminations, ODT, and output drive strength

settings are appropriate.

Observe

DQ/DQS

on a scope at the memory. View the alignment of the signals and

analyze the signal integrity during both writes and reads.

Observe the Address and Command signals on a scope at the memory. View the

alignment and analyze the signal integrity.

• Verify the memory parts on the board(s) in test are the correct part(s) set through the

MIG tool. The timing parameters and signals widths (that is, address, bank address)

must match between the RTL and physical parts. Read/write failures can occur due to a

mismatch.

• Verify SDRAM pins are behaving correctly. Look for floating or grounded signals. It is

rare, but manufacturing issues with the memory devices can occur and result in

calibration failures.

• If Data Mask (DM) is not being used, ensure DM is tied Low at the memory with the

appropriate termination as noted in the memory data sheet.

• Measure the

CK/CK_n

DQS/DQS_n

, and system clocks for duty cycle distortion and

general signal integrity.

• If internal V

REF

is used, ensure the constraints are set appropriately according to the

Xilinx Constraints Guide. When the constraints are applied properly, a note similar to

the following appears in the

.bgn

BitGen report file:

There were two CONFIG constraint(s) processed from example_top.pcf.

CONFIG

INTERNAL_VREF_BANK12

= 0.75

CONFIG INTERNAL_VREF_BANK14

= 0.75

• Check the

iodelay_ctrl

ready signal.

• Check the PLL lock.
• Check the

phaser_ref

lock signal.

• Bring the

init_calib_complete

out to a pin and check with a scope.

Send Feedback

Содержание Zynq-7000







































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Zynq-7000

Отзывы:

Похожие инструкции для Zynq-7000

Бренды по названию

Популярные бренды

Xilinx Zynq-7000, Руководство пользователя

Результаты поиска

Содержание Zynq-7000

Отзывы:

Похожие инструкции для Zynq-7000

Бренды по названию

Популярные бренды