1143100
SmartPAC PRO User Manual
122
Chapter 3 – SmartPAC PRO Initialization Mode
Disable Loss Rotation
(INITIALIZATION
– SYSTEM INIT – DISABLE/ENABLE LOSS ROTATION)
Press Disable Loss Rotation to prevent loss-of-rotation errors.
Using SmartPAC PRO with a Link-motion Press
If your SmartPAC PRO is installed on a link-motion press, you need to determine whether to use
NORMAL MOTION or LINK MOTION for your RESOLVER MOTION MODE setting (see page
87) and, if you are using a servofeed with a Wintriss ServoFeed Interface (SFI), how to compensate
for the different upstroke and downstroke speeds on your link-motion press.
To determine the proper RESOLVER MOTION MODE setting to use, run the press in Continuous
mode (if applicable) and observe the press speed.
•
If press speed varies between the upstroke and downstroke, set RESOLVER MOTION MODE to
LINK MOTION (refer to
, below)
•
If press speed does not vary during the stroke, leave RESOLVER MOTION MODE set to
NORMAL MOTION and install and zero the resolver so that bottom dead center equals 180
.
This setting will likely result in a top-dead-center reading of less than 360
, but this value is
acceptable in these circumstances. Refer to Chapter 2 for instructions on installing and zeroing
the resolver.
Setting Link Motion
If press speed in Continuous mode varies during the stroke, set RESOLVER MOTION MODE to
LINK MOTION as follows:
1.
Access the Main Initialization Menu, then select POSITION SENSOR.
2.
Move the highlight bar to the RESOLVER MOTION MODE item, and press ENTER to toggle
the setting to LINK MOTION.
3.
Press Exit to return to the Main Initialization menu. Turn the PROG/RUN keyswitch to RUN,
and run the press to observe the behavior of the Press Speed value.
NOTICE
If WaveFormPAC is installed on your press and RESOLVER MOTION MODE is set to LINK
MOTION, WaveFormPAC comparison screens will not display the Ram Velocity.
Содержание SmartPAC PRO
