Windhager DuoWIN Скачать руководство пользователя страница 21

Страница: 21 / 76

For the Installer

2.4.4 Note before installation

Confirm hydraulic piping:

– Windhager hydraulic piping DUO 001 is used, or

– Hydraulic piping is completely installed on-site

Confirm flue gas connection:

– Windhager flue gas connection set DUO 002 is used, or

– Flue gas connection is completely installed on-site; see also point 2.4.5.

2.4.5 Wood gasification boiler: Installing the flue connection adapter

– Only for wood gasification boiler with flue connection adapter (accessories)

Standard installation of blower housing is directly on the boiler – Fig. 20

flue connection at top.

With the adapter (accessories), the blower housing is located outside of the cladding – Fig. 23. The flue
connection is steplessly adjustable from left to right – Fig. 22.

– Unscrew 4 interior nuts in the blower housing (Fig. 20) and remove the housing. Do not remove the seal –

Fig. 21.

Fig. 20 Blower housing directly on boiler –

standard

Fig. 21 Seal on boiler

Note!

If the wood gasification boiler LogWIN Klassik pellets ready is already installed, continue with sec-
tion 2.4.27.

Содержание DuoWIN













































































Результаты поиска

Содержание DuoWIN

Отзывы:

Похожие инструкции для DuoWIN

Бренды по названию

Популярные бренды

Windhager DuoWIN, Руководство по сборке

Результаты поиска

Содержание DuoWIN

Отзывы:

Похожие инструкции для DuoWIN

Бренды по названию

Популярные бренды