Videonics AB-1 Edit Suite страница 95 Скачать руководство пользователя | Manualshive

Страница: 95 / 151

background image

• PROTO (Protocol) is the type of control protocol used by your VCR or camcorder.
Check your VCR/camcorder manual to determine the correct choice. Choices are:

LANC Sony Control-L

PANA Panasonic Control-M

232 RS-232 (Baud Rate and Character Format choices
display)

422 RS-422

IR Infrared; Record VCR only. (CMD choices display)

NONE Not used, or a noncontrollable video source is
attached to the corresponding port on a mixer/switcher.

• VCR is the VCR Table number to use. See Appendix A for a full list of choices.

• PREROLL is the number of seconds the VCR/camcorder should preroll before a scene
is played. Typically this value is 05–five seconds. It may need to be increased to 12 for
play VCRs/camcorders if insert editing is used and a VCR with PANA protocol is the
Record VCR.

For Record VCRs, only VCRs that require a preroll are prerolled. For the most part, this is
VCRs with RS-422 protocol. Leave the value at 05.

• TCSRC (Time Code Source) and TC (Time Code Type). TCSRC specifies whether
time code is sent through the Edit Control Cable (INT) or through an audio/video cable
attached to the Time Code IN port (EXT). TC specifies the type of time code being used.

- If Time Code is not used, select TCSRC=INT and TC=NONE.

- For most RS-232 and RS-422 VCRs, select TCSRC=INT and TC=NONE, VITC,
LTC or RCTC, depending on which time codes are available and selected on the
VCR.

- For LANC VCRs and camcorders with RCTC, select TCSRC=INT and
TC=RCTC.

- For LANC and PANA play VCRs with VITC or LTC striped on the play tape,

«
...
93
94
95
96
97
...
»

Содержание AB-1 Edit Suite
























































































































































Отзывы:

Нет отзывов

Похожие инструкции для AB-1 Edit Suite

Бренд: NEC Страницы: 3

Бренд: On-Q/Legrand Страницы: 14

CONTRIBUTE 3-CONTRIBUTE PUBLISHING SERVER

Бренд: MACROMEDIA Страницы: 30

ClearPass Guest 3.9

Бренд: Aruba Networks Страницы: 518

BREEZE-MANAGING EXTERNAL BREEZE REPORTS

Бренд: MACROMEDIA Страницы: 18

IronKey Workspace Provisioning Tool 1.0

Бренд: Imation Страницы: 19

ALTIRIS 6 INVENTORY SOLUTION

Бренд: Symantec Страницы: 2

COLDFUSION STUDIO 4.5-USING COLDFUSION...

Бренд: MACROMEDIA Страницы: 236

WISE MOBILE DEVICE PACKAGE EDITOR 7.0 SP2

Бренд: Symantec Страницы: 22

Veritas CommandCentral 5.1

Бренд: Symantec Страницы: 52

Бренд: Seagate Страницы: 2

Бренд: Extreme Networks Страницы: 376

CLUSTER FOR ENTERPRISE LINUX 5.0

Бренд: Red Hat Страницы: 114

Бренд: GameShark Страницы: 15

Бренд: Oracle Страницы: 140

15606-011408-9320 - MAP R6.3 CPU MODEL-UPG 4/5 MIN 2 CPUS INITL

Бренд: Autodesk Страницы: 190

225A1-05A111-1001 - AutoCAD Electrical 2009

Бренд: Autodesk Страницы: 255

ENTERPRISE LINUX AS 2.1 -

Бренд: Red Hat Страницы: 210

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды